EuroLite 50531140 User Manual

EuroLite 50531140 User Manual

Led strip 4in1 zone rf controller, wireless remote control for single- and multi-colored leds 12-24 v, set receiver and remote control, receiver

Advertisement

Quick Links

LED Strip 4in1 Zone RF Controller
Wireless remote control for single- and multi-colored LEDs 12-24 V
No. 50531140 Set (receiver and remote control)
No. 50531145 Receiver
USER MANUAL
EN
SAFETY INSTRUCTIONS
Only use the product according to the instructions given herein. Damages due to
failure to follow these operating instructions will void the warranty! We do not assume
any liability for any resulting damage.
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the
warranty/guarantee will be null and void.
Unauthorized rebuilds or modifications of the product are not permitted for reasons of
safety and render the warranty invalid.
This product is not a toy. Keep it out of the reach of children. Do not leave packaging
material lying around carelessly.
Keep this device away from rain and moisture. Indoor use only.
Protect the product against excessive humidity and heat. The recommended
temperature is -5 to +45°C.
Before taking into operation, check upon possible damages. If defective, the product
must not be taken into operation.
This product is maintenance-free, except for occasional cleaning. You can use a
slightly dampened cloth for cleaning. Never use alcohol or solvents.
Maintenance and service operations are only to be carried out by authorized dealers.
Thank you for purchasing this LED control system. The wireless
receiver is especially designed for control of single- and
multi-colored (CW+WW, RGB, RGBW) LED strips requiring an
operating voltage of 12 V and 24 V direct current. The receiver is
operated by wireless control (2.4 GHz) via the remote control. 4
control zones are available. Multiple receivers can be assigned to
the zones as desired and controlled via the same remote control,
either separately or in groups. As the receivers forward the radio
signal, a large range can be covered and all color settings run in
sync. The maximum power consumption of a channel must not
exceed 6 A and of all LEDs connected 24 A. The connection must
be made by skilled personnel only. Please read these operating
instructions carefully before using the product. They contain
important information for the correct use of your product. Please
keep them for future reference.
1 • EN
www.eurolite.de

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 50531140 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for EuroLite 50531140

  • Page 1 LED Strip 4in1 Zone RF Controller Wireless remote control for single- and multi-colored LEDs 12-24 V No. 50531140 Set (receiver and remote control) No. 50531145 Receiver www.eurolite.de USER MANUAL Thank you for purchasing this LED control system. The wireless receiver is especially designed for control of single- and multi-colored (CW+WW, RGB, RGBW) LED strips requiring an operating voltage of 12 V and 24 V direct current.
  • Page 2: Installation

    INSTALLATION Overview DIP switch to select LED type Connectors for LEDs Power connection: 12-24V DC Setup Install the receiver in a suitable spot and remove the covers from the terminals. • Connect the LEDs to the negative and positive OUTPUT terminals (V+ = common positive pole, •...
  • Page 3 INSTALLATION Application example 1: Single-color LEDs V+→V+, CH1→V‒, CH2→V‒, CH3→V‒, CH4→V‒ Application example 2: White LEDs (CW+WW) with variable color temperature V+→V+, CH1→CW, CH2→WW, CH3→CW, CH4→WW Application example 3: RGB LEDs V+→V+, CH1→R, CH2→G, CH3→B, CH4→not connected Application example 4: RGBW LEDs V+→V+, CH1→R, CH2→G, CH3→B, CH4→W 3 •...
  • Page 4: Wireless Connection

    WIRELESS CONNECTION For the remote control to work together with the receiver, the two devices first have to be paired. There are four separate control zones. Multiple receivers can be assigned to the four zones as desired and controlled with a mutual remote control. The receivers can be operated in different modes so it is possible to operate each zone with different LED types.
  • Page 5 WIRELESS CONNECTION Pairing the remote control with the receiver When paired, the receiver can be controlled via the remote control. Step Procedure Remarks 1) If the receiver has been paired before, it has to be reset to factory settings before it can be paired again. Connect the LEDs and switch on the 2) Provided that they are within the range receiver.
  • Page 6 WIRELESS CONNECTION Pairing multiple remote controls Each remote control is delivered with its own code preconfigured. If you use multiple remote controls, the code of one remote control needs to be copied to the other remote controls for them to operate in sync successfully. Step Procedure Remarks...
  • Page 7: Operation

    OPERATION Single-color LEDs If the DIP switch has been set to the operating mode DIM, the following functions can be controlled with the remote control. The remote control switches to stand-by mode after 8 seconds of inactivity and can be reactivated by pressing any button. RF signal indicator Dimmer ring Mode...
  • Page 8 OPERATION White LEDs with variable color temperature If the DIP switch has been set to the operating mode CCT, the following functions can be controlled with the remote control. RF signal indicator Color ring Mode Nightlight Brightness ‒ (5 levels) Brightness + (5 levels) Brightness ‒...
  • Page 9 OPERATION RGB LEDs If the DIP switch has been set to the operating mode RGB, the following functions can be controlled with the remote control. RF signal indicator Color ring Mode White 6 basic colors 6 basic colors Brightness + (1024 levels) Brightness ‒...
  • Page 10 OPERATION RGBW LEDs If the DIP switch has been set to the operating mode RGBW, the following functions can be controlled with the remote control. RF signal indicator RGB off RGB on Farbring Mode White on/off White brightness + White brightness ‒ RGB brightness ‒...
  • Page 11: Technical Specifications

    TECHNICAL SPECIFICATIONS Remote control Carrier frequency: 2.4 GHz Range: ca. 20 m Battery: 2 x 1,5V AAA LR03 (not included) Standby current: <18 µA Operating current: 20 mA Dimensions (LxWxH): 164 x 45 x 26 mm Weight: 0.95 g Receiver Power supply: 12-24 V DC Standby current:...
  • Page 12: Protecting The Environment

    PROTECTING THE ENVIRONMENT Disposal of old equipment When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information.

This manual is also suitable for:

50531145

Table of Contents