Secure H-Channels To Posts - Timbertech Impression Rail Express Installation Manual

3
6
75.70 OUTSIDE OF CAPS
75.44 OUTSIDE OF POSTS

Secure H-channels to Posts

4
69.44 INSIDE OF POSTS
• Measure and mark 3 7/8" above upper
bottom snap.
75.70 OUTSIDE OF CAPS
75.44 OUTSIDE OF POSTS
Rail System, use crossover brackets on 2"
69.44 INSIDE OF POSTS
A
posts. (Page 7, Dia. #11-12)
• Using (4) - #8x3/4" self-drilling screws, attach
the upper 2 clips to the post.
• Using (4) - #8x3/4" self-drilling screws,
secure the upper clips to the unpunched
H-channel.
3.88 TYP
SUPPORT LEG
• Snap top rail snap over the unpunched
77.43 OUTSIDE OF SKIRTS
H-channel until properly seated.
NOTE: Do not install top snaps yet if
lighting wires will be run through top rails.
A
3.88 TYP
4X #8 X 3/4"
STRAIGHT
77.43 OUTSIDE OF SKIRTS
TEK SCREW
CLIP
Dia. #11
STRAIGHT
6X CLIP DETAIL
CLIP
6X CLIP DETAIL
3
4
3
(Dia. #10) For Continuous Top
3" END POSTS
(Dia. #11)
SKIRT
3" END POSTS
(Dia. #12)
(Dia. #13)
SKIRT
SUPPORT LEG
3" POST DETAIL
4X #8 X 3/4"
4X #8 X 3/4"
TEK SCREW
SELF-DRILLING
SCREWS
3
Installing Impression Rail
2
REVISIONS - BALLOONS DENOTE CHANGES
REV. DESCRIPTION
A
Dia. #10
2
CROSSOVER
3" X 3"
BRACKET
3.88
3 7/8"
POST CAP
2" POST
44.78
44 7/8"
42.33
42 5/16"
2" BASE
SKIRT
4X BASE
36.20
36 3/16"
44.78
MOUNTING
SCREWS
4X BASE
MOUNTING
30.06
30 1/16"
SCREWS
42.33
3" POST
2" POST
BASE
BASE
MOUNTING
MOUNTING
STRUCTURE
3.36
3 3/8"
STRUCTURE
2" POST DETAIL
SECTION A-A
Dia. #12
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
DRAWN
TOLERANCES:
SURFACE FINISH: 125 RMS
CHECKED
ANGULAR: .5 DEG
LINEAR: .X .02 ENG APPR.
.XX .010
MFG APPR.
.XXX .005
THIRD ANGLE INTERPRET GEOMETRIC
TOLERANCING PER: ASME Y14.5-2009
PROJECTION:
MATERIAL
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
UNLESS OTHERWISE SPECIFIED:
FINISH
DRAWING IS THE SOLE PROPERTY OF
DIMENSIONS ARE IN INCHES
UltraLox. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN TOLERANCES:
DO NOT SCALE DRAWING PERMISSION OF UltraLox. SURFACE FINISH: 125 RMS
ANGULAR: .5 DEG
2
LINEAR: .X
RAIL PANEL CLIP DETAIL
.XX
.XXX
THIRD ANGLE
PROPRIETARY AND CONFIDENTIAL
PROJECTION:
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UltraLox.
ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF UltraLox IS NOT PERMITTED.
MATERIAL
FINISH
DO NOT SCALE DRAWING
2
Page 14
Open Mid-Rail Stair Panels
1
DATE APPROVED
7/31/2018 ZAG
CAP
IMPRESSION TOP RAIL
REVISIONS - BALLOONS DENOTE CHANGES
UNPUNCHED H-CHANNEL
REV. DESCRIPTION
A
CAP
STRAIGHT CLIP
2X WALL MOUNTING
SCREWS
IMPRESSION TOP RAIL
IMPRESSION
WALL MOUNT
UNPUNCHED H-CHANNEL
BOTTOM SNAP
STRAIGHT CLIP
STRAIGHT CLIP
BOTTOM RAIL
WALL MOUNT
H-CHANNEL
3.88
MOUNTING
STRUCTURE BOTTOM SNAP
.5" X .75" PICKET
2X WALL
MOUNTING
SCREWS
STRAIGHT CLIP
H-CHANNEL
BOTTOM RAIL
H-CHANNEL
WALL MOUNT
STRAIGHT CLIP
2X WALL
MOUNTING
BOTTOM SNAP
SCREWS
36.20
.5" X .75" PICKET
RAIL PANEL
3" POST BASE
30.06
(SKIRT HIDDEN
H-CHANNEL
FOR CLARITY)
WALL MOUNT DETAIL
STRAIGHT CLIP
POST
BOTTOM SNAP
RAIL PANEL
CLIP
3" POST BASE
3.36
NAME DATE (SKIRT HIDDEN
4X #8 X 3/4"
ZAG 7/31/18 FOR CLARITY)
4X #8 X 3/4"
SELF-DRILLING
TITLE:
SHOP DRAWING,
TEK SCREWS
SCREWS
IMPRESSION TOP RAIL,
H-CHANNEL UNPUNCHED
3" END POSTS,
SECTION A-A
H-CHANNEL
36" PICKETS, OPEN MIDRAIL,
6' SECTION
SIZE DWG. NO.
B
NAME DATE
ZAG 7/31/18
DRAWN
SCALE: 1:10 WEIGHT: SHEET 1 OF 1
TITLE:
CHECKED
IMPRESSION TOP RAIL,
1
.02 ENG APPR.
.010
MFG APPR.
.005
36" PICKETS, OPEN MIDRAIL,
INTERPRET GEOMETRIC
SHEET 2 OF 2
TOLERANCING PER: ASME Y14.5-2009
SIZE DWG. NO.
PROPRIETARY AND CONFIDENTIAL B
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
UltraLox. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN
SCALE: 1:10 WEIGHT:
PERMISSION OF UltraLox.
Express
™
1
DATE APPROVED
7/31/2018 ZAG
B
B
Dia. #13
A
A
REV
A A
SHOP DRAWING,
3" END POSTS,
6' SECTION
REV
A A
SHEET 1 OF 1
1