Setting The Clock (Remote Control Only); Listening To The Ipod; Ipod Button; Clock/Timer Button - Sharp CD-DH790N Operation Manual

Setting the clock (Remote control
only)
CD
USB
In this example, the clock is set for the 24-hour (0:00)
display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button.
Press the or
12-hour display and then press the MEMORY button.
The 24-hour display will appear.
"0:00"
(0:00 - 23:59)
The 12-hour display will appear.
"AM 12:00"
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
"AM 0:00"
(AM 0:00 - PM 11:59)
4
To adjust the hour, press the
then press the MEMORY button. Press the
button once to advance the time by 1 hour. Hold it
down to advance continuously.
5
To adjust the minutes, press the
then press the MEMORY button. Press the
button once to advance the time by 1 minute.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will be displayed when
the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as
follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK"
does not appear in step 2, step 3 (for selecting the 24-hour
or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1
Clear all the programed contents. [Refer to "Factory
reset, clearing all memory" on page 20 for details.]
2
Perform "Setting the clock" from step 1 onwards.
TAPE
button to select 24-hour or
or button and
or button and

Listening to the iPod

Supported iPod models:
● iPod nano (software 1.2 above)
● iPod mini (software 1.2 above)
th
● iPod (5
connector equipped Click Wheel model)
● iPod (4 th
connector equipped Click Wheel model)
● iPod nano (2
● iPod nano (3
● iPod nano (4
● iPod classic (software 1.0.3 above)
● iPod touch (software 1.1 above)
● iPod touch (2
Caution:
Please update your iPod unit to the latest software version
from Apple's homepage before using it.
Notes:
● Once the iPod is connected to the unit it will begin
charging.
● The iPod unit cannot be charged while the main unit is
in the stand-by mode or during USB mode.
Auto power on function:
When you press any of the following buttons, the unit turns
on.
● iPod button on the remote control: The unit turns on
and the iPod function is activated.
●
/ button on the main unit: The unit turns on and
playback of the last function will start (iPod, CD,
TUNER, USB, TAPE, AUDIO IN).
■ iPod adaptor connection
Notes:
or
● iPhone is not supported by this system.
● You can use an audio cable to connect your iPod to the
AUDIO IN jack if:
1.
your iPod adaptor does not fit into the iPod dock on
or
the main unit.
2.
you have an iPod that does not have an iPod
adaptor.
3.
you have an iPod that does not have an iPod 30 pin
connector.
E-7
generation) (software 1.3 above) (Dock
generation) (software 3.0.2 above) (Dock
nd
generation) (software 1.0.0 above)
rd
generation) (software 1.0.3 above)
th
generation) (software 1.0.3 above)
nd
generation) (software 2.1 above)