Table of Contents
Advertisement
Installing the refrigerator
•
Before installing your new
fridge,
read all safety instructions in this
instructions
below.
•
Place the fridge on the
sturdy,
level floor for quieter
enough to support the fridge when it is fully loaded
•
If the refrigerator is to be placed on
carpet,
aware that placing the refrigerator on carpet may mean that heat from the compressor
may cause the carpet to fade.
This appliance is designed to be freestanding only and should not be recessed or built in.
•
•
Do not tilt the fridge more than
45°
from upright when moving it.
•
Avoid areas where the appliance would be exposed to direct
heater, radiator, etc.),
extreme cold ambient temperatures or excessive moisture and high
humidity.
Installing it in the coolest area of the room will save energy consumption and running
cost.
WARNING!
Handle with care! Do not apply force to any part such as
•
the condenser or
door.
The metal rails on the bottom
underneath of this refrigerator may have sharp
always unpack and handle with
care.
Do not drag the unit:
place it carefully in position to avoid scratching the floor.
Space requirements
•
Place the unit so there is enough space for the door to
open.
•
Ensure that air can circulate freely around the back of the
cabinet,
which is necessary to cool the compressor and
condenser.
Allow at least 100mm clear space at the back
and 50mm at the sides of the unit.
Levelling
•
The appliance must be installed level to work properly.
the unit is not
level,
the door and magnetic seal alignments will not be covered
•
To level the
unit,
adjust one or both leveling feet at the base of the unit.
manual,
then follow the
operation.
Ensure that the floor is strong
.
support it with a wooden board underneath. Be
sunlight,
sources of heat
edges,
so
If
properly.
Mechanical Controller
The mechanical thermostat temperature control and the LIGHT on/off switch is located at below
places:
(stove,
Setting the Temperature Control:
•
To start the
refrigerator,
the desired
cooling.
setting the thermostat control
•
The settings 0(OFF) - 7(MAX) regulate the interior temperature of the
Setting 0(OFF)
Setting 1(MIN) = lowest setting (warmest internal
Setting 7(MA X)
NOTE: The refrigerator temperature will vary depending on the quantity of cans/
bottles stored and on the frequency with which the door is
temperature varies in different parts of the refrigerator the back of the refrigerators
is coldest. Please keep the cans/bottles away from rear wall to avoid freezing the
bottles and to allow the circulation of cold air.
NOTE:
power is still being
will turn on
period,
Defrosting
The surface of the evaporator ices up when the Refrigerator is
part of
operation.
and cleaned to avoid unnecessary energy consumption and inefficient operation.
Remove all items inside and unplug the Refrigerator.
•
After defrosting
•
Reconnect to the mains supply to run the
•
Replacing the Bulb
If the bulb is suddenly faulty, contact an authorized professional, do not service by yourself.
turn the temperature control to the position corresponding to
The temperature of the refrigerator is controlled by adjusting/
knob,
located on the top in the cabinet.
=
not operating (Please press the knob and turn to get the
temperature)
=
Highest setting (Coldest internal
temperature)
Thermostat
0(OFF)
position indicates the refrigerator is turned off although
supplied.
By turning the thermostat dial to the
automatically.
When the refrigerator is not to be used for an extended
disconnect the plug and leave the door partially
If the frost layer is more than
3mm/1/8"
thick
,
clean the refrigerator and allow it to
dry.
refrigerator.
refrigerator.
"0"
position)
opened.
The internal
left,
the refrigerator
open.
working.
This is an entirely normal
,
the Refrigerator must be defrosted
Hide quick links:
Advertisement
Table of Contents
