Table of Contents
Related Manuals for Sonosax SX-LC8+
Summary of Contents for Sonosax SX-LC8+
- Page 1 SX-R4+ LINEAR FADER EXTENSION MODULE SONOSAX SX-LC8+ USER MANUAL Version 1.0 August 2019 Audio equipment manufacturer SONOSAX SAS S.A. Ch. de la Naz 38 CH-1052 Le Mont-sur-Lausanne Switzerland http://www.sonosax.ch sonosax@sonosax.ch...
-
Page 2: Table Of Contents
Equipment (WEEE) Directive 2002 / 96 / EC and must not be disposed of in domestic household waste. RoHS Sonosax complies fully with Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS) SX-LC8+ User Manual... -
Page 3: Introduction
PRODUCT COMPATIBILITY This product requires the SX-R4+ runs with firmware revision 3.5 or greater Like all SONOSAX products, the SX-LC8+ was build without any compromise in terms of quality, using only the best components available and successfully passing strict quality controls. -
Page 4: Panel Description
2 Panel Description Front Panel F1 to F8 Linear faders Internal slate/com microphone P1 to P8 Function push-buttons Slate/com mic push button. Mic is enabled as long as this button is kept pressed. Device Serial Number marking C1, C2 Record start push-button. A short Binder 8-pin to connect with a SX-R4+ or press starts the recording or adds an another SX-LC8+. -
Page 5: Operating Instruction
The SX-LC8+ is powered by the SX-R4+ and is automatically detected by the SX-R4+ (firmware revision 3.5 and upper). The following tables illustrate all connection cables options. Sonosax cable reference number is on top right of each drawing: SX-LC8+ User Manual... - Page 6 As soon as the SX-LC8+ is detected, a new sub-menu appears on the main menu screen, bottom right. SX-LC8+ User Manual 6/11...
-
Page 7: Sx-Lc8+ Screen
SX-LC8+ Screen When pushing the SX-LC8+ button in the main menu, the following screen is displayed: where: • (A) SX-LC8+ connection status • (B) SX-LC8+ setup button • (C) active SX-LC8+ fader gauges • (D) secondary SX-LC8+ fader gauges (when two SX-LC8+ are connected) The fader gauge color shows the fader position. -
Page 8: Function Push-Button Assignation
Function Push-button Assignation The 8 push buttons below the linear faders are assignable function keys. They can be assigned in the SX-R4+ SETUP / SYSTEM / PUSH BUTTONS menu. The following screen captures shows the default assignation: First line shows the function called with a short press. Second line shows the function called with a long press. -
Page 9: Setup Menu
Setup Menu The SX-LC8+ setup menu includes two different zones: 1. 8 presets buttons to store and recall user configurations 2. The slate/com microphone settings The presets are labeled P1 to P8. To store the current configuration, press and hold the corresponding button until a confirmation message appears. -
Page 10: Specifications
4 Specifications Internal slate/com Microphone Preamplifier Sampling Frequency 48 kHz Resolution 16-bit Output format Power Input Voltage +3.3 to 5.5 V on Binder 8-pin Power consumption 65 mW (REC LED OFF, mic OFF) 125 mW (REC LED OFF, mic ON) 77 mW (REC LED ON, mic OFF) 137 mW (REC LED ON, mic ON) Mechanical... -
Page 11: Connector Pin Assignments
5 Connector Pin Assignments Binder 8-pin RS422 TX LOW MIC AES HI MIC AES LOW DC INPUT RS422 RX HIGH RS422 RX LOW RS422 TX HI SX-LC8+ User Manual 11/11...
Need help?
Do you have a question about the SX-LC8+ and is the answer not in the manual?
Questions and answers