Advertisement
Available languages
Available languages
1
IR
IN1
IN2 IN3 IN4 IN5
OFF
ON
9
Overview
1
2
1 IR sensor for the remote control
3
10
signals
2 LEDs IN 1 – IN 5 to indicate the input
4
5
selected (8)
3 Button "Switch" to select an input
11
4 LED , lights up when the signal
switch has been switched off
5 Button /I to switch on and off
−HDMI SWITCH−
HDMI™ Signal Switch
These instructions are intended for users without any specific
technical knowledge. Please read the instructions carefully prior
to operation and keep them for later reference.
1 Safety Notes
The units (signal switch and power supply unit) correspond to all
relevant directives of the EU and are therefore marked with
WARNING The power supply unit uses dangerous mains
voltage. Leave servicing to skilled personnel
only. Inexpert handling may result in electric
shock.
•
The units are suitable for indoor use only. Protect them
against dripping water, splash water and high air humidity.
The admissible ambient temperature range is 0 – 40°C.
•
Do not place any vessel filled with liquid on the unit,
e. g. a drinking glass.
•
The heat produced inside the signal switch must be dissipated
via the air vents; therefore, never cover the air vents.
•
Immediately disconnect the power supply unit from the socket
1. if the power supply unit or the signal switch is visibly dam-
aged,
2. if a defect might have occurred after the unit was dropped
or suffered a similar accident,
3. if malfunctions occur.
In any case, the units must be repaired by skilled personnel.
•
For cleaning only use a dry, soft cloth; never use water or
chemicals.
•
No guarantee claims for the units and no liability for any
resulting personal damage or material damage will be
accepted if the units are used for other purposes than orig-
inally intended, if they are not correctly connected or oper-
ated, or if they are not repaired in an expert way.
If the units are to be put out of operation definitively,
take them to a local recycling plant for a disposal
which is not harmful to the environment.
2 Applications
This signal switch allows you to connect five video signal sources
(DVD player, laptop, satellite tuner etc.) with a resolution up to
"4K Ultras HD" to a display unit (monitor, TV set, projector).
The desired signal source can be selected on the signal switch
or via remote control.
2
3
4
5
Switch
/I
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
©
6
7
8
HDMI OUT
HDMI IN5
DC 5V
6 Connection for the power supply unit
7 Signal output HDMI OUT
8 Signal inputs HDMI IN 1 – 5
9 Buttons
OFF and ON
10 Buttons 1 – 5 for direct selection of an input (8)
11 Input selector buttons
(as an alternative)
3 Operation
1) The remote control is operated by means of a 3 V button
cell (type CR 2025). If the remote control is supplied with a
battery inserted, remove the protective film (to protect the
battery from being discharged) from the battery holder. The
remote control is now ready for operation. When you press a
button on the remote control, always point the remote con-
trol at the IR sensor (1). There must be no obstacles between
.
the sensor and the remote control.
To insert or replace the battery, pull out the battery holder
on the rear. Insert the battery with the positive pole facing
up. If the remote control is not in use for a longer period of
time, always remove the battery to prevent damage due to
battery leakage.
Never put batteries in the household waste. To
protect the environment, always take them to a
special waste disposal, e. g. collection container at
your retailer.
2) Connect the signal sources to the inputs HDMI IN (8). Con-
nect the display unit to the output HDMI OUT (7).
3) Connect the power supply unit provided to the jack DC 5V
(6) and to a mains socket (230 V/ 50 Hz).
4) Use the button
/I (5) or ON (9) to switch on the signal
switch. The LED IN (2) of the most recent input selected (8)
will light up.
5) To switch to another input, press the button Switch (3) or
press 1, 2, 3, 4, 5 (10), ⋀ or ⋁ (11) on the remote
control.
6) After operation, use the button /I (5) or OFF (9) to switch
off the signal switch. The LED
switch is not in use for a longer period of time, disconnect
the power supply unit from the socket. It will consume some
power even when the signal switch has been switched off.
4 Specifications
Max. signal resolution: . . . UHD (4K), supporting HDR
Number of inputs: . . . . . . .5
Connections: . . . . . . . . . . .HDMI connectors, type A
Power supply: . . . . . . . . . .via power supply unit provided
Ambient temperature: . . . .0 – 40 °C
Dimensions (W × H × D): . .159 × 22 × 65 mm
Weight: . . . . . . . . . . . . . . .246 g
Subject to technical modification.
8
8
8
HDMI IN4
HDMI IN3
HDMI IN2
(4) will light up. If the signal
and connected to 230 V/5 0 Hz
A-1947.99.01.11.2018
8
HDMI IN1
Advertisement
