Accessories - Motorola R-2001D Operator's Manual

• ACCESSORIES SUPPLIED
FRONT COVER - The front cover protects the front
panel and its components during transit or while the
Analyzer is not in use. The front cover stun:s
the power
cord, antenna, cables. and other equipment needed for
on-site servicing. PN #15·80335A70.
ANTENNA - The fused BNC connected antenna re-
ceives off-the-air signals. PN #TEKA-24A.
BNC to Type N Adapter. PN #58-84300A98.
DC POWER CONNECTOR KIT. PN #RPX-4097A.
In-Line Wattmeter Adapter. PN #RTL-4055B.
MANUAL - The Operator's Manual contains descrip-
tions and instructions for properly using the Analyzer.
PN #68P81069A66-0.
Oscilloscope
&
Meter Probe - A probe
(xl),
with
attachments, provides general servicing needs.
PN #RTL-4058A.
POWER CORD - The three-conductor cord powers
the Analyzer by AC and charges the optional battery
pack. Its right-angle design allows the Analyzer to stand
on end. PN #30-80336A36.
SUN SHADE - Snap the Sun Shade over the CRT
screen to observe displays even in bright sunlight.
PN #15-80335A55.
TEST MICROPHONE. PN #RTM-4000B.
12 VDC POWER CONNECTOR KIT. PN #RPX-4097A.
• OPTIONAL ACCESSORIES
BATTERY PACK - A
13.6
volt battery attaches di-
rectly to the back of the Analyzer to provide 50 minutes
of continuous operation. Built-in circuitry charges the
battery when the power switch is in Off or Standby posi-
tion. If battery power falls below 11 volts, a warning ap-
pears on the CRT. The battery can be installed in the
field but it cannot be used in conjunction with IEEE-448
Interface Bus or Blower. PN #RTP-1002A.
DELUXE TELESCOPING ANTENNA. PN #RTA-
4000A.
600 OHM LINE MATCHING TRANSFORMER
Use for 600 ohm balanced lines. PN #RTL-1003A.
PROTECTIVE CANVAS COVER - A rugged, padded
fabric cover protects the Analyzer from excessive field
wear. PN #RTL-4056B.
RF DETECTOR PROBE. PN #RTL-4075A.
1
TRANSIT CASE. PN #RTL-4065A.
1-4
• MODEL OPTIONS
• Cellular Test Functions - Model R-2008D provides
capability in one test instrument for servicing traditional
PM
eommunje~tjons ~nd.
with the
cellular option, the
new cellular radio systems:
• CELL-TO-MOBILE SIGNALING ACCEP-
TANCE TESTS
• MOBILE-TO CELL SIGNALING ACCEP-
TANCE TESTS
• AUTOMATIC RF TESTS
• MANUALLY SELECTED RF TESTS.
• High Stability (HS) Oscillator - Use this oscillator
to improve stability over the standard TCXO time
base to
+ / -
5
X
10-
8
maximum error, over the
temperature range of 0 to 55°C. A front panel LED
(Oven Ready) indicates when the ovenized crystal has
stabilized.
MODELS (See Specifications)
R-200ID Basic Model
R-200ID/HS
R-200lD/HSI220
R-2002D/HS
R-2002D/HSI220
R-2008D/HS
R-2008D/HSI220
R-2009D/HS
R-2009D/HSI220
• IEEE-488 STANDARD INTERFACE BUS
This option enables using the Analyzer as a program-
mable measurement instrument. For example, An-
alyzer Model R-2002D when combined with the suit-
able programmable controller and applications soft-
ware becomes the heart of an automated RF test sys-
tem. Control or monitor all of the Analyzer's func-
tions via the IEEE Bus. Perform full sequential test
routines, quickly and repetitively, with little operator
interaction.
• MODULE SERVICE KIT
The Extender Board Kit aids servicing the Analyzer's
modules with printed circuit board edges. Use with
A2, A3, A4, A5, A6, A7, A9, and A12 modules.
PN #RPX-4379A.