Koala Kare KB110-SSWM Manual page 2

MATERIALS:
18 gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density polyethylene with
Microban Antimicrobial additive interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel
mounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contoured
changing surface area is 442 sq in (2873 sq mm) and comes complete with nylon safety straps and bag hooks.
OPERATION:
Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-density
polyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance
requirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99 sanitary liners.
Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installed accord-
ing to the manufacturer's instructions.
INSTALLATION:
To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenter
perform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of support-
ing significant weight and can accommodate the supplied installation hardware. The Koala Bear Kare® Baby Changing
Station meets ADA regulations when properly installed.
Drilling holes and mounting the station:
1. Remove the station from the shipping container and check for any freight damage. Identify the best location for
installing the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequate
operating clearance.
2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all of
included hardware may be required for proper installation.
3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32"
stud center. If possible, locate the wood or metal wall studs for fastening the changing station in the desired
location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit is
installed into the stud. Use toggles (supplied) for holes on the other side.
4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5"
(1156mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with
this mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate the
bottom of the station 28" (711mm) from the floor and the top of the bed at 33" (838mm) from floor.
Using Wood Screws:
If the wall has wood studs on 16" or 32" centers, drill 1/8" pilot holes at the marks and use the four 1/4" x 3" panhead
tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a 7/32" masonry drill until you
hit the stud, then proceed to drill 1/8" pilot holes into the studs and use the four 1/4" x 3" panhead tapping screws with
supplied washers.
Using Toggle Fasteners:
If the wall has wood studs that are not on 16" or 32" centers, has metal studs, or an underlying surface of concrete block,
drill with a 1/2'' masonry bit. A minimum of 2-1/2" of inside wall space is required for toggles to turn. Insert supplied
toggles and tighten, locate station over toggles, then use supplied 1/4'' x 3" Phillips Panhead machine screws with
supplied washers.
SPECIFICATION:
Baby changing station shall have 18 gauge, type 304 satin stainless steel exterior finish with high-density polyethylene
with Microban Antimicrobial additive interior. Design of unit shall be surface-mounted. Unit shall be equipped with a
pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-
length steel-on-steel hinge. Unit shall have Microban Antimicrobial embedded into plastic material. No hinge structure
shall be exposed on interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardware
included. Unit shall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F2285-04 (formerly
ASTM PS125) Standard Consumer Safety Performance Specification for Diaper Changing Tables for Commercial Use,
ANSI Z535.4 Product Safety Signs and Labels, German TUV Technical Inspection Association, ASTM G21 Antifungal and
ASTM G22 Antibacterial Standards or local code if more stringent installation requirements are applicable for barrier-free
accessibility. Unit shall comply with ADA regulations when properly installed. Bed shall have smooth concave changing
area with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-in Liner Dispenser for use with 3-
ply chemical-free biodegradable sanitary liners, universal instruction graphics, and safety messages in 6 languages. Unit
shall be backed by manufacturer's 5-year limited warranty on materials and workmanship, and a 5-year replacement
warranty against vandalism. Unit shall be manufactured in the U.S.A.
Baby Changing Station shall be model KB110-SSWM of Koala Kare Products, A Division of Bobrick, 8962 S.
Quentin St., Centennial, CO 80112 USA, Tel: 1-888-733-3456 or 303-539-8359, Web: www.koalabear.com
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice.
KB110-SSWM Revised 7/06 Printed in U.S.A.
© 2006 by Koala Kare Products, A Division of Bobrick.