Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for GE CAS GPS Node II
- Page 1 CAS GPS Node II User Manual PROD1116 DOCU0142 Rev A...
-
Page 2: Table Of Contents
CAS-GPS Node II User Manual Contents Document Revision ................................3 Warnings ...................................4 Manufacturer Details ................................4 Scope ....................................5 CAS-GPS Node type variants ..............................5 CAS-GPS Node V2V variants ..............................5 CAS-GPS NODE TEMPERATURE VARIANTS ........................5 Abbreviations ..................................6 Definitions ..................................6 Transport ..................................6 Storage ....................................7 Unpacking of Equipment ..............................7 Installation ..................................7 Test &... -
Page 3: Document Revision
GE further makes no representation or warranty of accuracy of these materials and GE will have no responsibility or liability for any error or omission in these materials. -
Page 4: Warnings
1 Warnings Installation should be in accordance with the installation procedures defined by GE Digital Mining Technology and must only be performed by authorized and qualified installers. The CAS product is a driver’s aid and should not be relied upon as the primary means of reducing the risks of high potential interactions. -
Page 5: Scope
CAS-GPS Node II User Manual 3 Scope This user manual covers the following variants of the CAS-GPS node product range. All PROD1116 products are electrically equivalent with differences residing in available connection methods to suit the various installations of the product. PROD1116-τν(X) τ) The two-digit suffix of the part number define the product type (... -
Page 6: Abbreviations
GE Digital Mining Technology immediately. Notify GE Digital Mining Technology within 7 days (maximum) in case of shortages or discrepancies, according to the packing list. This action will help ensure a speedy resolution to any perceived problems. Keep a record of all claims and correspondence. -
Page 7: Storage
Check for damage during transit. • Confirm that all the components required are present. If the set of components received is incomplete or damaged contact GE in a timely way to minimize delays. Take care when unpacking the equipment to avoid damage. -
Page 8: The Cas Gps Node Product Family
CAS-GPS Node II User Manual 9 The CAS GPS Node Product Family Principle of System Operation The CAS-GPS Intelligent multi-purpose NODE is the front-end transponder for enabling situational awareness of fleet vehicles, infrastructure and personnel The NODES form an integral component of the CAS -GPS system when paired with one of the CAS-GPS host devices such as the light vehicle display or the heavy vehicle rugged IVU running the CAS-GPS user interface software. -
Page 9: Prod1116-Lν(X) - Light Vehicle Node
CAS-GPS Node II User Manual 9.2.2 PROD1116-Lν(X) - Light Vehicle Node The Light Vehicle Node is suitable for a fixed installation on light vehicle types. The Light Vehicle Node can act as your primary fleet monitoring radio in light vehicles where self-test functions are not required. As a secondary Node this product enables automatic real-time functional health monitoring of a PROD1116-Eν... -
Page 10: Prod1116-Pν(X) - Type P Node
CAS-GPS Node II User Manual 9.2.4 PROD1116-Pν(X) – Type P Node The Versatile Type P Node contains a magnetic base which communicates with the CAS-GPS User Interface via wireless Personal Area Network connection. The unit is battery powered for mobile use or can be wired to a 12V-24Vdc power supply for fixed position installations. -
Page 11: Cas-Gps Node Operation
CAS-GPS Node II User Manual CAS-GPS Node operation 9.3.1 On System Start-up Immediately after starting the system and before putting it into service, perform a quick check of the CAS-GPS user interface status ICONs. Check that none of the icons are Red indicating a fault condition, if so your CAS-GPS system is not functioning correctly and its operation and your visibility within the fleet cannot be assured! Stationary Objects without a permanent display should have functions regularly checked on a temporarily paired CAS- GPS user interface display as detailed in the installation manual for the stationary object. -
Page 12: Vehicle In Motion
CAS-GPS Node II User Manual 9.3.2 Vehicle in Motion When your vehicle is moving, you can operate using your normal safe operating procedures. The Display will sound an alarm to gain your attention if there is another vehicle that is getting too close. A quick glance at the display will show the location, type, ID, heading and speed of other vehicles. -
Page 13: Type P Node Installation
CAS-GPS Node II User Manual Type P Node Installation The Type P Node is attached to the vehicle using a magnetic base. The Node must be installed on the vehicle such that:- • It has a flat smooth and clear surface to fix to •... -
Page 14: System Charging Warnings
CAS-GPS Node II User Manual System Charging Warnings Only use charge cables provided. Charging can be plugged into a normal vehicle 12V accessory power outlet. Charging can be carried out during operation. Do not pass charging cable through vehicle doors or windows. Do not use damaged power cords or plugs. -
Page 15: Service, Maintenance & Disposal
CAS-GPS Node II User Manual 10 Service, Maintenance & Disposal 10.1 Equipment Service 10.1.1 Display Unit Clean screen surface with a clean dry soft cloth - Do not use solvents or cleaners on the screen surface! • Check for physical damage to screen surface. •... -
Page 16: Authorized Representatives
F: +612 4389 2355 www.getransportation.com/mining www.getransportation.com/mining Mexico India COMERCIALIZADORA MINERA DEL NORTE, S.A. DE C.V. GE India Industrial Private Ltd. Ave. H. Colegio Militar No. 2000-B A-18, First Floor Col. Las Fuentes Okhla Industrial Area Phase II Piedras Negras, Coahuila New Delhi –... -
Page 17: Warranty Terms
CAS-GPS Node II User Manual 12 Warranty Terms Equipment and Parts: 15 months from delivery, or 12 months from when system is placed in service (whichever occurs first). Modifications to this product without written consent from the manufacturer or its designated authorised representatives will void all warranty obligations. -
Page 18: Regulatory Information
13.1 Declaration of Conformity with FCC rules for electromagnetic compatibility We, GE Digital Mining Technology, of 3 Co-Wyn Close, Fountaindale, NSW, 2258, Australia declare under our sole responsibility the products:... -
Page 19: Industry Canada Compliant
CAS-GPS Node II User Manual 13.2 Industry Canada Compliant This Class B digital apparatus complies with Canadian ICES-003. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 13.2.1 Concerning Radio Transmitters This device complies with Industry Canada’s licence-exempt RSSs. -
Page 20: Life Support Policy
GE Digital Mining Technology customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify GE Digital Mining Technology from any and all damages resulting from such improper use or sale.