Page 1
Quark-elec Manual QK-G022G GSM Remote Controller Manual Features Remote monitoring and control by mobile phone GSM SMS message Connects to up to 2 alarm inputs and 3 Relay outputs Automatic alarm by SMS message when alarm input is triggered ...
Quark-elec Manual Contents Set up overview ............................... 3 Introduction ................................4 Hardware ................................. 5 Enclosure ................................6 Preparing SIM card ..............................7 5.1. Insert SIM into the SIM card slot ......................... 7 Configuration ................................8 Status LED‟s................................8 Alarm function and digital connection ........................9 Relay working modes ............................
(you can check by putting the SIM card in a mobile phone) Installation: 1. Download and install the app for mobile phones. https://www.quark-elec.com/downloads/apps/ 2. Select G022G location: location must be indoors and not exposed to water or high humidity.
Quark-elec Manual Introduction The G022G series remote controller is a versatile device which can be connected to many electronic devices in homes, offices, factories or wherever required. The standard G022G includes two digital alarm inputs, three independent relay switches. It allows operators to control and monitor remote equipment or machines using SMS (Short Message Service) via the GSM network.
Quark-elec Manual Hardware Figure 2: General view of the control module (V1.9) Figure 3: G021 mechanical drawing (V1.5) https://www.quark-elec.com 5 of 29 2018...
Quark-elec Manual Enclosure The enclosure is made of IP56 Insulation Class 2 plastic. External dimensions: 145 x 90 x 41 mm. Figure 4: GK-G022 (with enclosure) Figure 5: Enclosure drawing. Measurements in mm https://www.quark-elec.com 6 of 29 2018...
Quark-elec Manual Preparing SIM card Please ensure: The SIM must operate on the GSM (2G) network. Most network providers provide 2G cover, check with your supplier. There is credit on the SIM (we recommend automatic top-ups) The SIM is not PIN protected ...
Quark-elec Manual Configuration The following steps are required to configure G022G for first time use: Insert the SIM card into controller box Power up Send „88888888‟ as SMS to the G022G controller. If successful, the user will receive the message „Your phone has been registered‟.
Quark-elec Manual Alarm function and digital connection G022G has two external alarm input connectors and various inputs can be connected to them. For example, door/windows sensors, smoke alarms, carbon dioxide detectors, motion sensors, thermostats, temperature/wind detectors, and moisture detectors. Using these sensors/detectors, G022G can be set up as a protection/alarm and response system.
Quark-elec Manual Relay working modes 9.1. Normal open/ normal closed wiring options The G022G is equipped with three digital output relays for connection to equipment to be controlled. The relays can be set up in normal open and normal closed positions. This gives the customer the advantage of having it set as a failsafe if there is a power loss or for timing the relay to open or close with delays.
Quark-elec Manual 9.3. Self-lock vs. latching mode The G022G allows for two different working modes; self-lock control and latching control. Self-lock allows for the usual function of the relay where a command from the operator or the device to change is needed. If input from an alarm then the relay will stay locked on until the command “EXTRT”...
Quark-elec Manual 9.4. Delay time setting on latching mode Working in latching mode, operators can configure G022G with different delay times for Relay 1 and Relay 2 by setting the delay time jumpers. Delay time settings for Relay 1 and Relay 2...
Quark-elec Manual 10. APP The G022G APP provides a touch sensitive, user friendly interface. The app will write the text messages for you and send them from your mobile for operators to control G022G. The app also allows for up to two G022G devices to be controlled from a single mobile operator.
Quark-elec Manual 10.1. Setup After installation, on opening the APP for the first time, users will see the following page for the login process. This login page allows for users to input up to two devices and control them separately: Figure12: Login page https://www.quark-elec.com...
Quark-elec Manual 10.2. Set QK controller SIM number Input the number of the SIM card which is inserted in G022G. All command SMS messages will be sent to this number via the APP. Figure 13: Login details successful Once the SIM card number has been stored, the APP will reply with a successful message shown below the login button.
Quark-elec Manual 10.3. Register SIM cards G022G allows one mobile phone to function as the main terminal and up to 3 additional phones to function as control terminals. The following interface allows the operator to register, delete and check the SIM card numbers:...
Quark-elec Manual 10.4. Setting the clock on the QK controller G022G can automatically execute actions at the time set by the operator. To do this, the real time clock on the QK controller should be set. This page allows the operator to check and set the time on G022G. When using this function, the CR2032 battery should be used on the module.
Quark-elec Manual 10.5. Check relay working mode G022G has three individual relays which support two working modes, namely self-lock and latching control. When working in latching mode, the relay takes active action for a few seconds (depending on the time setting on the jumpers on the board.) and then reverts to normal status.
Page 19
Quark-elec Manual G022G can also report the relay working status via SMS to the operators. Figure 19: Check relay working status https://www.quark-elec.com 19 of 29 2018...
Quark-elec Manual 10.6. Rename control terminals The control terminals can be renamed as a meaningful name in APP. Figure 20: Rename control terminals https://www.quark-elec.com 20 of 29 2018...
Quark-elec Manual 10.7. Control panel The control panel provides the main operating interface for turning relays on and off and setting timers. Figure 21: Control panel interface for relay https://www.quark-elec.com 21 of 29 2018...
Quark-elec Manual 10.8. Track and trace The track and trace function allows for the G022G device to be located using Google maps. The speed and the position information can also be checked on APP for G022G variant (with GPS receiver).
Quark-elec Manual 11. Command and response SMS Remember that all SMS text commands must always be sent using CAPITAL letters. Do not add spaces or any other characters. Function Command Note Register SIM cards Register main SIM card 88888888 Register the main mobile terminal with G021 module by sending „88888888‟...
Page 24
Quark-elec Manual refers to Self-lock mode. For example, INCH1SELF2 means, relay 1 works in Latching control mode and relay 2 works in Self-lock mode. Check relay working WHOACTIVE G022G will reply with the relay working status status information similar to the following format: „R1, R2, R3: ACTIVE;...
Page 25
Quark-elec Manual the setting is successful. By click the replied link message, G022G module position will be displayed on Google map. Monitoring/alarm input Releases relay status EXTRT After it has been triggered by the external which is triggered by the signals, the related relay will be locked in the normal state.
9 V - 245 V Rated voltage on relay < 2000 W RF main socket power rating For more technical information and enquiries please go to the Quark-elec forum: https://quark-elec.com/forum/ info@quark-elec.com For sales and purchasing information, please email us at: https://www.quark-elec.com...
G022G. Open the link in any web browser, Google map with the position icon will be displayed. The following is an example of the page. Figure 26: Google map with G021 current position For more technical information and enquiries please go to the Quark-elec forum: https://quark-elec.com/forum/for info@quark-elec.com sales and purchasing information, please email us at: https://www.quark-elec.com...
15. Limited warranty and notices Quark-elec warrants this product to be free from defects in materials and manufacture for one year from the date of purchase. Quark-elec will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour.
Page 29
Quark-elec Manual https://www.quark-elec.com 29 of 29 2018...