Subscribe to Our Youtube Channel
Related Manuals for Futek LCF Series
Summary of Contents for Futek LCF Series
- Page 1 LCF Series Tension and Compression Sensor Family Manual Sensor Solutions Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com...
-
Page 2: Table Of Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... -
Page 3: Features
Tension bases allow for tension inline loading available on select models . models . TEDS Integrated TEDS calibration information available on some models . Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... -
Page 4: Mechanical Installation
3. Install in a dry, clean • An extraneous how-to guide can be environment, unless IP rating found at: http://www .futek .com/files/ allows for other environments pdf/Extraneous_Load_Factors/How_To_ Calculate_Extraneous_Loads .pdf Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software... -
Page 5: Maximum Installation Torque
2100 .0 LCF500/LCF505 25000 10000 .0 50000 15000 .0 LCF501/LCF506 12500 10000 .0 25000 15000 .0 LCF550/LCF555 100000 38000 .0 LCF551/LCF556 50000 38000 .0 Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... -
Page 6: Mounting And Installation
Active End 4. Load fixture must contact top Fixed End inner ring Further mounting suggestions: Load Plate Alignment couplers Rod-end bearings & yokes/clevis Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... -
Page 7: Bolt Torque And Tightening Pattern
1400 by thermal expansion and will maintain the Ø 11” 250K lb . 5/8-18 3000 specifications provided by FUTEK . For improved accuracy and reduced zero shift Ø 12” 400K lb . 3/4-16 4800 during mounting and bolt tightening make sure the plate is as flat as possible . -
Page 8: Cable Care And Routing
Polyester Good Good General Soft, flexible, easy to use Polyurethane Average Good Automation Soft, flexible, easy to use Not suitable for thermal chambers Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... -
Page 9: Electrical Installation
20 V LCF501 20 V LCF505 20 V LCF506 20 V LCF550 20 V LCF551 20 V LCF555 20 V LCF556 20 V Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... -
Page 10: Shield Usage And Connections
Transducer Electronic Data Sheet (TEDS) • A yearly calibration is recommended . But two points on the load cell’s Wheatstone IEEE1451 .4 standard is available for FUTEK verification and calibration period shall be bridge to generate a known, fixed output from... -
Page 11: Troubleshooting
• Calibration verified outputs are being • Sensor support is not ridged and firm . used . • Incorrect sensor output is utilized . Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com... - Page 12 • Sensor or instrument is exposed to • Confirm wiring and grounds are not ground loop with other equipment connected to unintended equipment grounds . ground . Sensor Solution Source Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software www.futek.com...
-
Page 13: Further Support Resources
• To send in your sensor or system for evaluation and repair visit our FUTEK RMA web page at: http:// www .futek .com/contact .aspx?form=repair • FUTEK contact information can be found online at: http://www .futek .com/contact • Warranty information can be found online at http://www .futek .com/remWarranty .aspx...
Need help?
Do you have a question about the LCF Series and is the answer not in the manual?
Questions and answers