Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pedelec Impulse 2.0
Summary of Contents for Pedelec Impulse 2.0
-
Page 2: Table Of Contents
Adjustments/maintenance/repair 7.4.4 Device settings 7.4.4.1 Display Transportation of the Pedelec 7.4.4.2 Drive 1.7.1 The Pedelec and your car 7.4.4.3 Miscellaneous 1.7.2 The Pedelec on trains 1.7.3 The Pedelec on aeroplanes 7.4.5 Personalize 7.4.6 Target cost 2 Composition of the vehicle... - Page 3 The purpose of this User Manual is to help you get the 5. Select “Open User Manual rom CD” or “Check for new most out of your Pedelec Impulse 2.0 and use it correctly. version of User Manual online”. Structure of the User Manual To call up the iles, you need the program Adobe Reader.
-
Page 4: Safety
WARNING regarding possible physical injury, increased Statutory requirements risk of falls or other injuries. The Pedelec, like all other bikes, must comply with the national regulations for road safety. Please observe the relevant explanations and general NOTE information provided in the “Original User Manual regarding possible damage to property or the | General”... -
Page 5: Battery
“Technical data” of the “Original User Manual | Use the battery solely for your Pedelec. General” (CD). The Impulse 2.0 mountain bike is an exception. Bike trailers may not be used on this Ideally, take the battery out of your Pedelec when bike. -
Page 6: Charger
There must be no highly combus- tible materials in the immediate vicinity. This also applies when charging the battery on the Pedelec. In this case, you must place the Pedelec so as to prevent any ire rom spreading quickly (exercise caution with carpeted loors!). -
Page 7: Motor
1.7.1 The Pedelec and your car feet or legs. You could burn yourself. If you transport your Pedelec on a bike rack, ensure that it Live parts may be exposed when you open covers is designed for the higher weight of a Pedelec. In order to or remove parts. -
Page 9: First Steps
Fitting the pedals CLOSE Closing the quick-release lever It may be that the pedals for your Pedelec have yet to be itted on delivery: The right pedal (marked with an “R”) is screwed clockwise into the right crank arm. The let pedal (marked with an “L”) is screwed anticlockwise into the let crank arm. -
Page 10: Quick Start
Charge temperature: 0°C to 45°C. charging, reinsert the battery into the holder on the Pedelec rom the let-hand side. Tilt the battery out- wards at an angle of roughly 45° as you do so. Move the battery into the upright position until the locking mechanism engages. -
Page 11: Battery
Charging the battery If you cannot feel any assistance, simply back- You can charge the battery whilst it is on the Pedelec pedal briely and then pedal forwards again to Chapter 4 “Quick start”. -
Page 12: Removing The Battery
Seat tube battery: Grip the battery by the handle To charge the battery safely, the charger must be and remove it rom the Pedelec by tilting it sideways. placed on a suitable surface. This should be dry In doing so, hold on tight to the battery to prevent it and non-lammable. -
Page 13: Installing The Battery
Seat tube battery: Insert the battery into the holder The LED of the charger lights up in green. The battery of the Pedelec rom the let by tilting it outwards at LEDs light up one by one to indicate the progress of roughly 45°. -
Page 14: Battery Information System
3 LEDs light up 67–51% •• 2 LEDs light up 50–34% • 1 LED lights up 33–17% 1 LED lashes 16–0% 5 LEDs lash quickly 0% or overloaded * 1st LED lashes Charging fault ** quickly Original User Manual | Pedelec Impulse 2.0... -
Page 15: Battery Management
If a fault occurs during this period, your specialist cycle on your Pedelec just before you set of. This will shop will replace the battery. Normal ageing and battery help to prevent the efect of the low temperature wear do not constitute a fault. -
Page 16: Storage
Do not ship batteries! A battery is a hazardous article which can overheat and catch ire in certain You can charge your Pedelec Impulse 2.0 directly via a conditions. charging socket in the battery. The battery can remain on the Pedelec whilst the charging operation is in progress. -
Page 17: Control Panel And Display
To activate the pushing assistance, press the button for three seconds. The Pedelec Impulse 2.0 can be controlled via two ele- ments. The control panel can be found on the handlebar grip; the display is located in the middle of the handlebar. -
Page 18: Display Small
7.2.1 Assistance indicator If you do not use your Pedelec for ten minutes, the The display shows you how much assistance the motor is system switches of automatically. If you subse- currently providing. -
Page 19: Units
The total number of kilometres covered. You can select the menu sub-items using the buttons • The display of kilometres covered during the on the control panel. You can conirm your selection by day and overall. Original User Manual | Pedelec Impulse 2.0... -
Page 20: Drive Data
“Conirm delete?”, and below it “Yes” or “No”. Select the desired item using the button. The selection is highlighted in bold. Conirm your selection by tapping the button. You are taken back to the menu sub-items. Original User Manual | Pedelec Impulse 2.0... -
Page 21: Drive
A change to the setting becomes necessary, for Average “Standard” example, when you have the tyres on your Pedelec exchanged for some of a diferent size. In order to continue to display the correct data, the new wheel circumference must be entered. -
Page 22: Miscellaneous
7.4.6 Target cost desired text rom the following options: Via the menu sub-item “Target cost”, you can access the sub-items: • Fuel price • Fuel consumption Ø • Fuel type • Power cost • Back Original User Manual | Pedelec Impulse 2.0... - Page 23 0 and 99 cents by using the buttons on the control panel to move in 1 cent steps. Pressing the button conirms your selection and then takes you back to the menu sub-item display. Original User Manual | Pedelec Impulse 2.0...
-
Page 24: The Motor
• How fast you ride. it on your Pedelec. When you set of on your Pedelec, the assistance increases as you build up speed until it reaches its As the battery discharges when the motor is in use, maximum, just before the highest assisted speed it generates enough heat to not lose too much of is achieved. -
Page 25: Riding Your Pedelec Eiciently
You can monitor and inluence the cost of your journeys your bike with too little air in the tyres, this can with the Pedelec yourself. You can reduce your consump- signiicantly increase the rolling resistance. This tion and therefore costs by following the tips for achieving applies to smooth surfaces in particular, e.g. -
Page 26: Troubleshooting
In this case, the charging Disconnect the battery rom the charger and present) is lashing red. current is too high consult your specialist cycle shop. Have the staf there check the battery and charger. Original User Manual | Pedelec Impulse 2.0... -
Page 27: Cleaning
In this way, you avoid a short-circuit and physical injury. 10.2 Motor Dirt should be removed rom the motor of your Pedelec Make sure when cleaning that water does not enter the regularly, ideally using a dry brush or a damp (not wet) charger. -
Page 28: Technical Data
IMPULSE LI-ION SEAT TUBE BATTERY Voltage 36 V 36 V Capacity 11 Ah 15 Ah Energy content 396 Wh 540 Wh Weight 2.85 kg 2.95 kg Charging time 4 hours 5 hours Cell 2.25 Ah 3.1 Ah Original User Manual | Pedelec Impulse 2.0... - Page 29 We hope you thoroughly enjoy using your new Pedelec with Impulse drive. Reproduction, in whole or in part, is not permitted without the consent of Derby Cycle Werke GmbH / Raleigh Univega GmbH. Subject to misprints, errors and technical modiications.
Need help?
Do you have a question about the Impulse 2.0 and is the answer not in the manual?
Questions and answers