Related Manuals for Rennsteig CM 25-1.3
Summary of Contents for Rennsteig CM 25-1.3
- Page 1 Owner‘s Manual Crimping Machine CM 25-1.3 Owner‘s Manual Crimping Machine CM 25-1.3 Please read instructions before starting any job! Rev.: 2016-05-31 1 / 15...
-
Page 2: Table Of Contents
Owner‘s Manual Crimping Machine CM 25-1.3 Table of Contents Preface Technical Data 2.1. Set-up/ Construction Transportation of Crimping Machine Limitations of Liability Requirements for Site Set-up Set-up of Crimping Machine Start-up/ Provisions/ Operation 7.1. Operational Safety 7.2. Protective Devices 7.3. -
Page 3: Preface
Owner‘s Manual Crimping Machine CM 25-1.3 1. Preface This owner’s manual is designed for you to get to know the crimping machine CM 25-1.3 and to properly operate the unit. The owner’s manual contains important instructions in order to operate the crimping machine safely and efficiently. -
Page 4: Set-Up/ Construction
Owner‘s Manual Crimping Machine CM 25-1.3 2.1. Set-up/ Construction Electronic Counter Mechanism Counter not resettable Square Counter Counter Bearing resettable Serial number plate Slide with adjusting collar and scale Swivel shaft to adjust working stroke Upper movable safety cover Pneumatic... -
Page 5: Transportation Of Crimping Machine
After carefully removing the packaging, the machine must be inspected for possible damages. Any discovered damages must be reported to the manufacturer RENNSTEIG WERKZEUGE GmbH Viernau. Please note that certain machine settings will be carried out later at the job site. -
Page 6: Set-Up Of Crimping Machine
Owner‘s Manual Crimping Machine CM 25-1.3 6. Set-up of Crimping Machine 1. Place the machine at the final work location. The adjustable feet Fig. 2/7 are used to place the machine firmly onto the work surface and is secured in place with the lock nuts Fig. -
Page 7: Start-Up/ Provisions/ Operation
Owner‘s Manual Crimping Machine CM 25-1.3 7. Start-up/ Provisions/ Operation 7.1. Operational Safety Before starting to use the crimping machine, some important rules need to be followed. The machine may only be used by trained and skilled personnel to avoid injury to persons and damage to the machine. The... -
Page 8: Adjusting The Working Stroke
Owner‘s Manual Crimping Machine CM 25-1.3 7.3. Adjusting the Working Stoke The crimping machine CM 25-1.3 is designed for various applications. The machine is equipped with two different working strokes. At applications up to 14 mm the automatic safety device is triggered. For structural small connectors and cable with a small cross section, a stroke of <6mm is sufficient. -
Page 9: Exchange Of Crimping Dies
The machine moves back to the starting position and is now ready to use. Upper 2 Adapter Lower Fig. 4 Before the CM 25-1.3 is connected to the air pressure supply line, remove the wrench from the square counter bearing. Rev.: 2016-05-31 9 / 15... -
Page 10: Change Of Crimping Position
• The machine moves back to the starting position and can now be used. Fig. 5 Before the CM 25-1.3 is connected to the air pressure supply line, remove the wrench from the square counter bearing. Rev.: 2016-05-31 10 / 15... -
Page 11: Exchanging The Adapters (For Larger System Measurements)
Owner‘s Manual Crimping Machine CM 25-1.3 7.6. Exchanging the Adapters (for larger System Measurements) The exchange of adapters is done as follows: • Close shut-off valve Fig.2/2, disconnect air pressure supply hose, open shut-off valve Fig.2/2 • Release the remaining air by pushing the reset button Fig.2/8, the safety cover will close automatically •... -
Page 12: Crimping Dimension Adjustment
Owner‘s Manual Crimping Machine CM 25-1.3 7.7. Crimping Dimension Adjustment In order to ensure fault-free crimping results, the CM 25-1.3 has been set at the factory in such a manner that the crimp dies are firmly closed at bottom dead center. Under certain conditions, for example, after changing the crimping dies, a readjustment may necessary to align the plunger stroke. -
Page 13: Electronic Counter Mechanism
Owner‘s Manual Crimping Machine CM 25-1.3 7.8 Electronic Counter Mechanism The Crimping machine CM 25-1.3 has two electronic counting mechanisms. The upper counter mechanism is a permanent counter, which cannot be set back by the operator. The lower counter can be reset. -
Page 14: Technical Documentation
Owner‘s Manual Crimping Machine CM 25-1.3 9. Technical Documentation Rev.: 2016-05-31 14 / 15... -
Page 15: Eu-Declaration Of Conformity
Owner‘s Manual Crimping Machine CM 25-1.3 10. EU-Declaration of Conformity according to EU Guidelines for Machines 2006/42/EG, Appendix II The construction of the Crimping Machine Type: CM 25-1.3 No.: Year of Construction: Was developed, constructed and manufactured in compliance with the EU- Guidelines for Machines...