Related Manuals for R2TECK NEXG1 R
Summary of Contents for R2TECK NEXG1 R
- Page 1 ZeroDelay Full-HD digital video transmission system NEXG1 R USER MANUAL Wuxi R2TECKCo.,Ltd.
-
Page 2: Table Of Contents
无锡人人行拍网络科技有限公司 Content 1. Easy way to start the device........................1 1.1 Operating steps and instructions......................1 2. Specification..............................2 3. Introduction..............................3 3.1 Disclaimer............................3 3.2 Profile..............................3 3.3 Intended usage............................. 3 3.4 Caution..............................3 4. Port definition...............................5 4.1 port............................... 5 5. Installation..............................7 5.1 installation............................7 6. -
Page 3: Easy Way To Start The Device
LINK light turn-on if the receiver connect to transmitter. HDMI monitor instruction (if installed the HDMI monitor): The monitor shows logo " NEXG1 R" after receiver connect to the power. After that, the monitor shows progress bar: Start-up / Selfcheck / Link. -
Page 4: Specification
无锡人人行拍网络科技有限公司 2. Specification Here list the detailed specification about NEXG1 R, as shown in Table 2.1.1. Table 2.1.1 List of specification Function specification Communication distance ≥400m (outdoor, no obstruction) Effective Radiated Power（EIRP） >10mw Receiving sensitivity -95dbm±2dbm Operating frequency 5220MHz Physics specification Operating Temperature -10~60℃... -
Page 5: Introduction
Thanks for purchasing the NEXG1 R from Wuxi R2TECK. Everyone need to read and understand this disclaimer before using the NEXG1 R. You are supposed to be accepted the disclaimer once the product is started to use. Please comply with the installation and using process indicated in this use manual. - Page 6 无锡人人行拍网络科技有限公司 NEXG1 R should not work when it is wet. Have to make sure it is dry when you use it. NEXG1 R is the high precise product, it is forbidden to beat and clash. Product life time is 2 years, quality warranty is 1 year.
-
Page 7: Port Definition
无锡人人行拍网络科技有限公司 4. Port definition 4.1 port 4.1.1Bottom side port Figure 4.2.1.1 schematic diagram of bottom side port [1]: BIND button, For bind transmitter and receiver. Press the button more than 5 seconds, 4 lights (WORK, LINK, HDMI, MOBILE) are all turn-off, then stop press the button, 4 lights flash one by one, when the LED light works well that means they are well binded. - Page 8 无锡人人行拍网络科技有限公司 [6]: MOBILE light, For monitor mobile(iPhone、iPad) connect status. Light status Description Operation Turn-on Mobile connect well Make sure the mobile connect Turn-off No mobile connect with the network, turn off the software then turn on again. 4.1.2 Right side port Figure 4.2.2.1 schematic diagram of right side port [1]: DC-12V port, For power supply, connect with 12V DC power supply.
-
Page 9: Installation
One end of HDMI connect to the monitor, another end of HDMI connect to the receiver. 5.1.3 Power cable installation Support 12V-DC power, suggest the output power is more than 1A. 5.1.4 Mobile APP installation IOS App installation: In App store, search the key word “r2teck” and download. -
Page 10: Bind
无锡人人行拍网络科技有限公司 6. Bind 6.1 Bind Function description: Reset the device to factory settings, bind one transmitter with one receiverand gives the pair the matching ID code. Operation method: the device LED light shows correctly, press BIND buttons on transmitter and receiveratthe same time and keep more than 5 seconds, all the LED light will turn off, then release the button. -
Page 11: Contact Info
Thanks for purchasing our device again. If you have any suggestion or need technical support, please visit our website or send us the email, also welcome to call us. Wuxi R2TECK Co., Ltd Address：Room307,Building of Cetus,Wuxi software park,111th Linghuavenue,new district ,Wuxi city,Jiangsu Province P.C.：214000... - Page 12 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.