Related Manuals for R2TECK NEXG1 T
Summary of Contents for R2TECK NEXG1 T
- Page 1 ZeroDelay Full-HD digital video transmission system NEXG1 T USER MANUAL Wuxi R2TECKCo.,Ltd.
-
Page 2: Table Of Contents
无锡人人行拍网络科技有限公司 Content 1. Easy way to start the device ........................1 1.1 Operating steps and instructions ......................1 2. Specification .............................. 2 3. Introduction ............................... 3 3.1 Disclaimer ............................3 3.2 Profile ..............................3 3.3 Intended usage ........................... 3 3.4 Caution .............................. 3 4. -
Page 3: Easy Way To Start The Device
无锡人人行拍网络科技有限公司 1. Easy way to start the device 1.1 Operating steps and instructions 1.1.1Transmitter Install the antennas. Install the camera. Connect transmitter to the power. There should be below instructions if the transmitter works well. After 15 seconds of power on, the WORK light will display the breathing effect, and the WORK light will loop from on to off on display. -
Page 4: Specification
无锡人人行拍网络科技有限公司 2. Specification Here list the detailed specification about NEXG1 T , as shown in Table 2.1.1. Table 2.1.1 List of specification Function specification Communication distance ≥400m (outdoor, no obstruction) Effective Radiated Power（EIRP） >10mw Receiving sensitivity -95dbm±2dbm Operating frequency 5200MHz... -
Page 5: Introduction
The r ight o f t he manual lay out , m odify and r elease on ly bel ong t o Wuxi R2TECK, Without t he authorization of Wuxi R2TECK, this use manual could not be copied or modified or released. - Page 6 无锡人人行拍网络科技有限公司 NEXG1 T should not work when it is wet. Have to make sure it is dry when you use it. NEXG1 T is the high precise product, it is forbidden to beat and clash. Product life time is 2 years, quality warranty is 1 year.
-
Page 7: Module Port Definition
无锡人人行拍网络科技有限公司 4. Module Port definition 4.1 port 4.1.1 Back side port Figure 4.1.1.1 schematic diagram of back side port [1]: Camera port: For connect the camera. 4.1.2 Side 1 port Figure 4.1.2.1 schematic diagram of side 1 port [1]: Work light, For monitoring the g transmitter operating status. Light status Description Operation... - Page 8 无锡人人行拍网络科技有限公司 Check whether the camera is Turn-off Does not connect with camera well connected. 4.1.3 Side 2 port Figure 4.1.3.1 schematic diagram of side 2 port [1]: Bind button, For bind the transmitter and receiver. (Both the transmitter and receiver are required to operate simultaneously).
-
Page 9: Contact Info
Thanks for p urchasing o ur dev ice again. I f y ou have any s uggestion or n eed t echnical s upport, please visit our website or send us the email, also welcome to call us. Wuxi R2TECK Co., Ltd Address：Room307,Building of Cetus,Wuxi software park,111th Linghuavenue,new district ,Wuxi city,Jiangsu Province P.C.：214000... - Page 10 无锡人人行拍网络科技有限公司 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.