Advertisement
ASSEMBLY INSTRUCTIONS
IMPORTANT: WE ADVISE YOU TO ASSEMBLE THE TENT ONCE BEFORE
GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE TENT.
NOTE: PLEASE LOOK AT THE REPLACEMENT PARTS DIAGRAM TO SEE HOW
YOUR FRAME IS ASSEMBLED.
TO PROLONG THE LIFE OF THE TENT FLOOR, SELECT A LEVEL, CLEAN AREA FOR
THE CAMPSITE. TO PREVENT DAMAGE TO THE ZIPPER, UNZIP THE DOORS TO
ALLOW AIR TO ENTER THE TENT.
TO IMPROVE THE WEATHER RESISTANCE OF YOUR TENT, IT IS ADVISABLE
TO USE SEAM SEALER TO COAT ALL EXPOSED SEAMS. YOU SHOULD APPLY
ONLY TO THE INSIDE SEAMS OF THE TENT AND UNDERSIDE OF THE TENT
FLY. IF APPLIED TO THE OUTSIDE OF SEAMS, DISCOLORATION OF YOUR
TENT MAY OCCUR. SEAM SEALER IS AVAILABLE IN THE CAMPING SECTION
OF ANY LOCAL SPORTING GOODS STORE.
Configuration 1
STEP 1: Spread the tarp out flat with
the logo facing upward.
STEP 2: Locate and extend the two
steel upright poles by pulling out each
wire-corded section and placing the
jointed ends into the connected pole
sections.
STEP 3: Insert the tip of the pole into the grommet at the corner of the
tarp that has 2 guy ropes connected. Lift up on the steel pole and raise
one side of the tarp. Place the foot on the bottom of the pole on the ground.
STEP 4: With one person holding the pole in an upright position a
second person needs to extend the two guy ropes at the corner of
the tarp. Make a loops at the opposite ends of the guy ropes, by using
slider as shown and place loop over a tent stake. Adjust slider to make
the guy ropes tight and stake to the ground at a 45° angle.
STEP 5: While the first person continues to hold the first pole in place
the second person should go to the opposite corner of the tarp and
Insert the tip of the pole into the grommet Lift up on the steel pole and
raise the second side of the tarp. Place the foot on the bottom of the
pole on the ground and tension the tarp between the two poles.
Continue to hold the pole under tension through Step 6.
STEP 6: The person holding the first pole should now be able to
let go. They should extend the two guy ropes at the corner of the
tarp. Make a loops at the opposite ends of the guy ropes, by using
slider as shown and place loop over a tent stake. Adjust slider to
make the guy ropes tight and stake to the ground at a 45° angle.
STEP 7: The guy ropes on the 2 corners of the tarp without the upright poles
should now be extended and staked to the ground at a 45° angle.
STEP 8: Check and adjust tension of all guy ropes to make sure the tarp is held
securely in place
Tent should appear
as shown.
A
Configuration 2
A
STEP 1: Spread the tarp out flat
with the logo facing upward.
STEP 2: Remove one guy rope from each of the corners with 2 guy ropes connected. Tie the guy
ropes to the webbing loops located at the grommets at the midway point of the two tarp sides.
STEP 3: Locate and extend the two steel upright poles by pulling out each wire-corded
section and placing the jointed ends into the connected pole sections.
STEP 4: Insert the tip of the pole into the grommet at midpoint on one
side of the tarp Lift up on the steel pole and raise one side of the tarp.
Place the foot on the bottom of the pole on the ground.
M O D E L W930 - Multipurpose Tarp Shelter
A
A
STEP 5: With one person holding the pole in an upright position a second person
needs to extend the guy rope from the webbing at the tip of the pole.
Make a loop at the opposite end of the guy rope, by using slider as
shown and place loop over a tent stake. Adjust slider to make the guy
rope tight and stake to the ground at a 45° angle.
STEP 6: While the first person continues to hold the first pole in place
the second person should go to the opposite side of the tarp and Insert
the tip of the pole into the grommet. Lift up on the steel pole and raise the
second side of the tarp. Place the foot on the bottom of the pole on the
ground and tension the tarp between the two poles. Continue to hold the
pole under tension through Step 7.
STEP 7: With one person continuing to hold the upright pole extend the guy ropes
at the corners of the tarp. Make a loop at the opposite end of the guy rope, by
using slider and place loop over a tent stake. Adjust slider to make the guy rope
tight and stake to the ground at a 45° angle.
Tent should appear
as shown.
STEP 10: Check and adjust the tension of all guy ropes to make sure the tarp is
held securely in place
NOTE: Sandbags are provided for use at the beach. Fill the bags with sand and
attach to the end of the guy ropes. Bury the bags in the sand to hold the tarp in place.
NOTE : To take down tarp, follow steps above in the reverse order. Place stakes
into stake bag and pole into the pole bag, which are provided. Make sure tarp
is clean and dry before storing. The tarp should be folded into equal parts
toward the center to distribute the bulk. Start a small tight roll, the width of the carry
bag, with the pole bag placed at the end of the tarp. Roll tarp to allow air to escape.
Once rolled, tie a string or rope around tarp to hold into place. Place tarp, frame
and stakes into carry bag.
Advertisement
