TREND VJS/TG/JIG Manual
  1. Manuals
  2. Brands
  3. TREND Manuals
  4. Measuring Instruments
  5. VJS/TG/JIG
  6. Manual
TREND VJS/TG/JIG Manual

TREND VJS/TG/JIG Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
VJS/TG/JIG
Please read these instructions before use.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VJS/TG/JIG and is the answer not in the manual?

Questions and answers

Related Manuals for TREND VJS/TG/JIG

Summary of Contents for TREND VJS/TG/JIG

  • Page 1 VJS/TG/JIG Please read these instructions before use.

  • Page 2: Table Of Contents

    VJS/TG/JIG TECHNICAL DATA Dear Customer Thank you for purchasing this Trend product, we Extrusion thickness 15.8mm hope you enjoy many years of creative and Extrusion width 54.0mm productive use. Working groove length 400mm Please remember to return your guarantee card Maximum width adjustment 70mm within 28 days of purchase.

  • Page 3: Safety

    VJS/TG/JIG SAFETY and balance at all times. Do not use recommended when working outdoors. Wear protective hair awkward or uncomfortable hand WARNING: positions. covering to contain long hair. Observe the safety regulations in the 17. Don’t abuse the cable. Never carry 5.

  • Page 4: Safety

    15. All fastening screws and nuts should be adhered to. Recommended speeds 4. When using a template guide bush, be tightened using the appropriate are shown in the Trend Routing ensure there is sufficient clearance spanner or key and to the torque Catalogue and/or website.

  • Page 5: Items Enclosed

    VJS/TG/JIG ITEMS ENCLOSED End Cap Pre-assembled Silver Pre-assembled Silver Black Pre-assembled Silver Black x 10mm Black ITEMS REQUIRED n Plunge router (or jigsaw/circular saw). n 30mm guide bush with minimum 8mm projection e.g. Ref. GB30/A. n T-Square. n Board with flat edge.

  • Page 6: Description Of Parts

    VJS/TG/JIG DESCRIPTION OF PARTS Alloy extrusion long 430mm with scale Machine screw M4 x 6mm (black-fixed) Alloy extrusion short 310mm with end cap O Machine screw M4 x 6mm (silver-adjustable) Machine screw M4 x 10mm (black-fixed for Bottom squaring butt...

  • Page 7: Assembly & Adjustment

    VJS/TG/JIG ASSEMBLY & ADJUSTMENT Sliding Stops n Slide the right hand and left hand sliding stop Using the drawing on page 5 as a guide. assembly into the bottom slot of the long extrusion that does not have a scale.

  • Page 8: Adjustment

    VJS/TG/JIG Adjustment Make sure The black screws are used to lock the brackets into the end of the extrusions. Once they are correctly fitted they the extrusion should not need to be adjusted. The silver screws is sub flush are the screws that allow for adjustment of the jig.

  • Page 9: Operation

    VJS/TG/JIG OPERATION Guiding the Router/Saw The jig can be used either with a router, or for Adjusting Frame for Size sawing using a jigsaw or circular saw. n Loosen the silver screws. n Router - to groove boards with a router fitted with a guide bush with a minimum 8mm n Set required size.

  • Page 10: Grooving With The Router

    VJS/TG/JIG Grooving with the router A recommended 30mm guide bush should be used with a minimum 8mm spigot projection e.g. Ref. GB30/A. To rout grooves, trenches and tenon’s the router Component base will sit on top of the extrusions, therefore...

  • Page 11: Cross Cutting With A Router

    VJS/TG/JIG Crosscutting with the router Cross-cutting with a Router The flat side of the router base can be used against the edge of the right hand extrusion for grooving or trimming. Ensure that the end of the front and back short extrusions are not proud, so they do not foul the base of the tool.

  • Page 12: Cross Cutting With A Saw

    Measure from the edge of left-hand side of ACCESSORIES the saw base plate to right side of cutting Please use only Trend original accessories. edge, this will give the offset. Ref. GB30A 30mm guide bush with 8mm spigot length.

  • Page 13: Spare Parts - Spare Parts List

    VJS/TG/JIG Please use only Trend original spare parts. VJS/TG/JIG - SPARE PARTS LIST v1.0 08/2007 Qty. Desc. Ref. Varijig T-Nut M4 WP-VJS/01 Varijig Short T-Nut M4 WP-VJS/01A Varijig Machine Screw M4 x 6mm Csk Zinc WP-VJS/02 Varijig Machine Screw M4 x 6mm Csk Black...
  • Page 14 VJS/TG/JIG VJS/TG/JIG - SPARE PARTS DIAGRAM v1.0 08/2007 -IB-...
  • Page 15 RECYCLABLE © Copyright Trend 2012. No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools...

Table of Contents