H3C S9500 Series Command Manual
Routing switches
Hide thumbs
Also See for S9500 Series:
- Command manual (1842 pages) ,
- Operation manual (1504 pages) ,
- Operating manual (76 pages)
Table of Contents
Advertisement
Quick Links
Command Manual - Link Aggregation Configuration
H3C S9500 Series Routing Switches
Chapter 1 Link Aggregation Configuration Commands............................................................ 1-1
1.1 Link Aggregation Configuration Commands...................................................................... 1-1
1.1.1 debugging lacp packet ............................................................................................ 1-1
1.1.2 debugging lacp state ............................................................................................... 1-1
1.1.3 debugging link-aggregation error ............................................................................ 1-2
1.1.4 debugging link-aggregation event ........................................................................... 1-3
1.1.5 display lacp system-id ............................................................................................. 1-3
1.1.6 display lacp timer..................................................................................................... 1-4
1.1.7 display link-aggregation interface............................................................................ 1-5
1.1.8 display link-aggregation summary........................................................................... 1-6
1.1.9 display link-aggregation verbose............................................................................. 1-7
1.1.10 lacp enable ............................................................................................................ 1-9
1.1.11 lacp port-priority..................................................................................................... 1-9
1.1.12 lacp system-priority ............................................................................................. 1-10
1.1.13 lacp timer slow..................................................................................................... 1-11
1.1.14 link-aggregation................................................................................................... 1-11
1.1.15 link-aggregation extend....................................................................................... 1-12
1.1.16 link-aggregation group description ...................................................................... 1-13
1.1.17 link-aggregation group mode .............................................................................. 1-14
1.1.18 port link-aggregation group ................................................................................. 1-15
1.1.19 reset lacp statistics.............................................................................................. 1-15
Table of Contents
i
Table of Contents
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for H3C S9500 Series
Summary of Contents for H3C S9500 Series
-
Page 1: Table Of Contents
Command Manual – Link Aggregation Configuration H3C S9500 Series Routing Switches Table of Contents Table of Contents Chapter 1 Link Aggregation Configuration Commands............1-1 1.1 Link Aggregation Configuration Commands..............1-1 1.1.1 debugging lacp packet .................... 1-1 1.1.2 debugging lacp state ....................1-1 1.1.3 debugging link-aggregation error ................ -
Page 2: Chapter 1 Link Aggregation Configuration Commands
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Chapter 1 Link Aggregation Configuration Commands 1.1 Link Aggregation Configuration Commands 1.1.1 debugging lacp packet Syntax debugging lacp packet [ interface interface-type interface-number [ to interface-type... -
Page 3: Debugging Link-Aggregation Error
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands undo debugging lacp state [ interface interface-type interface-number [ to interface-type interface-number ] ] { { actor-churn | mux | partner-churn | ptx | rx } * |... -
Page 4: Debugging Link-Aggregation Event
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Description Use the debugging link-aggregation error command to enable link aggregation error debugging. Use the undo debugging link-aggregation error command to disable link aggregation error debugging. -
Page 5: Display Lacp Timer
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Parameters None Description Use the display lacp system-id command to display the device ID of local system, including system priority and system MAC address. -
Page 6: Display Link-Aggregation Interface
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands 1.1.7 display link-aggregation interface Syntax display link-aggregation interface interface-type interface-number [ to interface-type interface-number ] View Any view Parameters interface { interface-type interface-number [ to interface-type interface-number ]: interface-type specifies port type and interface-number specifies port number. -
Page 7: Display Link-Aggregation Summary
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Table 1-2 Description on the fields of the display link-aggregation interface command Field Description Attached AggID Aggregation group ID for the specified port... -
Page 8: Display Link-Aggregation Verbose
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Type Ports Ports Type Port -------------------------------------------------------------------------- ------ none Shar GigabitEthernet3/1/1 none Shar Ethernet4/1/45 Table 1-3 Description on the fields of the display link-aggregation summary... - Page 9 Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Note that since the manual aggregation group cannot get the information of the peer end, every item of the peer end is displayed as 0, which does not indicate the actual status of the peer system.
-
Page 10: Lacp Enable
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Field Description Remote: Detailed information about the peer device, including local port, peer port index, port Actor Partner Priority Flag Oper-key priority, flag, operation key and device ID SystemID 1.1.10 lacp enable... -
Page 11: Lacp System-Priority
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Description Use the lacp port-priority command to configure port priority. Use the undo lacp port-priority command to restore the default port priority. Related commands: display link-aggregation verbose, display link-aggregation interface. -
Page 12: Lacp Timer Slow
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands 1.1.13 lacp timer slow Syntax lacp timer slow interval undo lacp timer slow View System view Parameters interval: Slow period timer value (in seconds), in the range of 1 to 30. The default is 30. -
Page 13: Link-Aggregation Extend
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Note: After a port is added to an aggregation group, the ARP configuration of the port will be lost. Related commands: link-aggregation group mode, port link-aggregation group. -
Page 14: Link-Aggregation Group Description
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands Examples # Enable aggregation resource extension. <H3C> system-view System View: return to User View with Ctrl+Z. [H3C] link-aggregation extend # Remove aggregation resource extension configuration. -
Page 15: Link-Aggregation Group Mode
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands 1.1.17 link-aggregation group mode Syntax link-aggregation group agg-id mode { manual | static } undo link-aggregation group agg-id View System view Parameters agg-id: Aggregation group ID, in the range of 1 to 31. IDs At present, you can configure the static and dynamic aggregation groups only. -
Page 16: Port Link-Aggregation Group
Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands 1.1.18 port link-aggregation group Syntax port link-aggregation group agg-id undo port link-aggregation group View Ethernet port view Parameters agg-id: Aggregation group ID, in the range of 1 to 31. IDs At present, you can add the static and dynamic aggregation groups only. - Page 17 Command Manual – Link Aggregation Configuration Chapter 1 Link Aggregation Configuration H3C S9500 Series Routing Switches Commands specify a port with the first interface-type interface-number or specify a port range with the interface-type interface-number to interface-type interface-number where the end port must be greater than the start port.
Need help?
Do you have a question about the S9500 Series and is the answer not in the manual?
Questions and answers