JVC KD-DV5606 Installation & Connection Manual

KD-DV5606/KD-DV5605/
KD-DV5604
Installation/Connection Manual
GET0654-004A
[U/UH/UI]
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations.
– it may obstruct the operation of safety devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look around carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, "DRIVER MUST NOT WATCH THE MONITOR WHILE
DRIVING." appears on the monitor, and no playback picture will be shown.
– This warning appears only when the parking brake lead is connected to the parking brake
system built in the car.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car's chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect speakers with a maximum power of more than 50 W (both at the
rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W,
change <AMP GAIN> setting to prevent the speakers from being damaged (see page 27 of the
INSTRUCTIONS).
• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when
removing this unit.
Parts list for installation and connection
If any item is missing, consult your JVC car audio dealer immediately.
A / B Hard case/Control panel
E Power cord
H Lock nut (M5) I Mounting bolt (M5 × 20 mm)

TROUBLESHOOTING

• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded? ; Are the "–" terminals of L and R speakers grounded in common?
Heat sink
C Sleeve D Trim plate
F Handles G Washer (ø5)
J Rubber cushion
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Do the required electrical connections.
*
When you stand the unit, be careful not to damage the fuse on the rear.
When using the optional stay
Stay (option)
Fire wall
Dashboard
Screw (option)
Install the unit at an
angle of less than 30˚.
Removing the unit
Before removing the unit, release the rear section.
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car's chassis using shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead grounded? ; Are the "–" terminals of L and R speakers grounded in common?
• This unit does not work at all.
* Have you reset your unit?
1
0110DTSMDTJEIN
EN
© 2010 Victor Company of Japan, Limited
*
Bend the appropriate tabs to hold
the sleeve firmly in place.
When installing the unit without
using the sleeve
In a Toyota car for example, first remove the car
radio and install the unit in its place.
Flat head screws—M5 × 8 mm (not supplied)
Pocket
Bracket (not supplied)