Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
HDMI Display Controller
AT-DISP-CTRL
The Atlona AT-DISP-CTRL is a compact display controller, designed for small meeting spaces
and huddle rooms. The DISP-CTRL detects connection of a source device with an active signal,
and then automatically sends a control command to turn on a display. Similarly, when the device
is disconnected, the DISP-CTRL delivers a command to turn off the display. The DISP-CTRL
can be configured to deliver pre-stored or user-programmed display control commands through
TCP/IP, RS-232, IR, or CEC. Additionally, this controller includes EDID and HDCP management
features, and can be powered locally or through standard Power over Ethernet (PoE). The DISP-
CTRL is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling,
as well as HDMI data rates up to 18 Gbps.
Package Contents
1 x AT-DISP-CTRL
2 x Mounting brackets
4 x Mounting screws
1 x 5 V DC power supply
1 x Installation Guide
IMPORTANT: Visit http://www.atlona.com/product/AT-DISP-CTRL for the latest firmware
updates and documentation.
1
Installation Guide
AT-DISP-CTRL
Advertisement
Table of Contents
Related Manuals for Panduit Atlona AT-DISP-CTRL
Summary of Contents for Panduit Atlona AT-DISP-CTRL
- Page 1 HDMI Display Controller AT-DISP-CTRL The Atlona AT-DISP-CTRL is a compact display controller, designed for small meeting spaces and huddle rooms. The DISP-CTRL detects connection of a source device with an active signal, and then automatically sends a control command to turn on a display. Similarly, when the device is disconnected, the DISP-CTRL delivers a command to turn off the display.
- Page 2 Installation Guide AT-DISP-CTRL Panel Descriptions Front AT-DISP-CTRL POWER AT-DISP-CTRL POWER HDMI OUT HDMI IN SOURCE HDMI OUT HDMI IN SOURCE AT-DISP-CTRL IP MODE Rear AT-DISP-CTRL RESET DC 5V RS-232 IR OUT IP MODE RESET DC 5V RS-232 IR OUT HDMI OUT IP MODE Connect an HDMI cable from this port to Press and release this button to set the IP...
- Page 3 Installation Guide AT-DISP-CTRL RS-232 / IR Connector The AT-DISP-CTRL provides both an RS-232 and IR port, which can be used to send turn-on/ turn-off commands to the display, when a source is connected to the AT-DISP-CTRL. Command configuration is handled through the web GUI. Refer to the User Manual for more information. It is not necessary to connect both RS-232 and IR emitters to control the display.
-
Page 4: Installation
Installation Guide AT-DISP-CTRL Installation Connect an HDMI cable from the HDMI OUT port to the display device. Connect an Ethernet cable, from the PoE LAN port, to a PoE-capable network switch. NOTE: The AT-DISP-CTRL is powered over Ethernet (PoE) using a PoE-capable network switch. -
Page 5: Mounting Instructions
Installation Guide AT-DISP-CTRL Mounting Instructions The AT-DISP-CTRL includes two mounting brackets and four mounting screws, which can be used to attach the unit to any flat surface. Position one of the mounting brackets, as shown below, aligning the holes on the side of the enclosure with one set of holes on the mounting bracket. - Page 6 Installation Guide AT-DISP-CTRL IP Configuration The AT-DISP-CTRL is shipped with DHCP enabled. Once connected to a network, the DHCP server (if available), will automatically assign an IP address to the unit. If the AT-DISP-CTRL is unable to detect a DHCP server within 15 seconds, then the unit will use a self-assigned IP address within the range of 169.254.xxx.xxx.
-
Page 7: Resetting To Factory Defaults
Installation Guide AT-DISP-CTRL Resetting to Factory-Defaults AT-DISP-CTRL POWER To reset the AT-DISP-CTRL to factory-default settings, press and hold the RESET button for approximately 5 seconds. Release the button when the RESET LED indicator begins to flash. The LED indicator will flash three times to indicate that the reset procedure has completed. HDMI OUT HDMI IN SOURCE... -
Page 8: Front Panel Led Indicators
Installation Guide AT-DISP-CTRL Front Panel LED Indicators The LED indicators on the front panel of the unit provide basic information on the current status of the AT-CTRL-DISP. POWER Description Solid green Unit is powered. Unit is not powered. • Check to make sure a USB to mini-USB cable is connected between the DC 5V / FW port and a computer. - Page 9 Installation Guide AT-DISP-CTRL Notes...
- Page 10 Installation Guide AT-DISP-CTRL Notes...
- Page 11 Installation Guide AT-DISP-CTRL Notes...
- Page 12 Installation Guide AT-DISP-CTRL Toll free US International atlona.com 877.536.3976 41.43.508.4321 • • © 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specifications and availability subject to change without notice. Actual products, product images, and online product images may vary from images shown here.