Page 1
CORDLESS ANGLE GRINDER CT1646 ORIGINAL INSTRUCTION SAVE THESE INSTRUCTIONS AND PRECAUTIONS. Please read the entire instruction manual before using the product and then save it for future reference. We reserve the right for any errors in text or images and any necessary changes made to technical data.
WARNING! For your own safety, read this manual and the general safety instructions carefully before using the appliance. Your power tool should only be given to other users together with these instructions. SYMBOLS The following symbols are used in this manual and/or on the machine: WARNING –...
Page 4
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Page 5
Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Page 7
danger and personal injury. Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool.
Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
Page 9
procedures or conditions and can be avoided by taking proper precautions as given below. a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up.
Page 10
intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
PRODUCT DESCRIPTION Spindle lock On/Off switch Inner flange Safety switch Outer flange Battery pack Grinding guard 10. Rubber-clad handle Side handle 11. Cutting-off guard (extra accessory, not included) Spanner OPERATING INSTRUCTIONS Important: Always remove the battery pack from the power tool before adjusting, servicing or repairing it.
Page 13
1. Press A and use wrench to loose part B. 2. If the grinding guard isn’t assembled, use the hex key to put the grinding guard(C) on the machine first. 3. Install the disc. 4. Press A and use wrench to tight part B. 5.
• Keep the battery charger away from rain or moisture. Exposure of an electrical device to water increases the risk of an electric shock. • Hold the tool and the battery pack firmly when installing or removing battery pack avoid any injury. 1.
The contacts on the battery pack and the charger must be kept clean. All replacement parts must be replaced by a trained electrician or an authorized service centre unless stated otherwise in this manual Cleaning Clean the angle grinder using a lightly moistened cloth. Only use mild cleaning agents, never solvents or corrosive chemicals TROUBLESHOOTING GUIDE Problem...
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. CORDLESS ANGLE GRINDER Product description: Model: CT1646 Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU Harmonized standards EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Page 20
CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...