Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for iDevices IDEV0005
Summary of Contents for iDevices IDEV0005
- Page 1 Welcome To INSTALLATION GUIDE...
-
Page 2: Table Of Contents
Contents Introduction From removing your old thermostat, to installing your new iDevices Thermostat, this easy-to- ® Introduction ............3 follow guide will take you through the process, step by step. In The Box ............4 Display ..............5 If at any time you require assistance, please Before You Start .......... -
Page 3: In The Box
System Mode - Mounting Hardware Connection Status Ambient Temperature Requires - Home Wi-Fi Network ® Fan Mode Desired Temperature - Free iDevices ® Connected App HVAC State - 24VAC Common Wire - Compatible Mobile Device (Visit iDevicesinc.com/ Compatibility) Tools AUTO - Phillips Screwdriver - Drill With 3/16”... -
Page 4: Before You Start
4. Check that your mobile device is compatible 8. Connect your iDevices Thermostat to your ® with the iDevices Thermostat at home network and pair it to your iDevices ® ® iDevicesinc.com/Compatibility. Connected app. 5. If this is a new installation, you will need to 9. -
Page 5: Abbreviations
Abbreviations Terminal Assignments HVAC: Heating, Ventilation, and Air For reference, standard wiring assignments for Conditioning system typical HVAC systems are provided below. HP: Heat Pump System. This type of HVAC Heat Pump Conventional system uses a compressor with a reversing valve Terminal Terminal System... -
Page 6: Installation Details
Wiring Chart 1. Gather the tools you will need and check below. Note: If you see any of the following that your iDevices Thermostat came with the wires, please contact our Customer Experience ®... - Page 7 9. Make sure you don’t have any 120/240V wires (look for thick black wires with wire 13. Set the mounting plate aside. Drill two holes nuts.) If you do, the iDevices ® (3/16” diameter) at the locations you Thermostat is not compatible have marked.
-
Page 8: Connecting To The App And Wi-Fi Network
Thermostat is now configured. ® from the Settings > Setup > Connect menu. Set In-App Preferences Connecting To The App And Wi-Fi Network ® In your iDevices Connected app, select the ® 1. Download and launch the free iDevices ®... - Page 9 Thermostat ® button in the upper left-hand corner. From to EMERGENCY HEAT mode. Adjust the here, you can edit the details of your iDevices temperature set point above the ambient ® Thermostat, organize it into a ‘Room’ and ‘Zone’, temperature in the room, and verify that the set schedules and create ‘Scenes’.
-
Page 10: Wiring Configuration
If G wire is not connected for a warm wiring configurations compatible with the air heating system, Fan On mode will not be available. iDevices Thermostat. Find the configuration that ® matches closely to your old thermostat and note... - Page 11 B. Heat Only (Two Stages) C. Cool Only (One Stage) Note: G wire is not required for hot-water baseboard or steam radiator systems. If G wire is not connected for a warm Thermostat Settings air heating system, Fan On mode will not be available. Stage: Non-HP | Type: HG Note: G wire is not required.
- Page 12 D. Cool Only (Two Stages) E. Heat (One Stage) and Cool (One Stage) Thermostat Settings Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for Stage: Non-HP | Type: HG Note: G wire is not required. However, if G wire is not connected, Fan On mode will not be gas/oil systems available.
- Page 13 F. Heat (Two Stages) and Cool (One Stage) G. Heat (One Stage) and Cool (Two Stages) Thermostat Settings Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for Stage: Non-HP | Type: HE for electric, HG for gas/oil systems gas/oil systems Note: G wire is not required.
- Page 14 H. Heat (Two Stages) and Cool (Two Stages) Heat Pump (One Stage) Thermostat Settings Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for Stage: HP | Type: HG | O/B Type: According to gas/oil systems previous thermostat setting Note: G wire is not required.
- Page 15 J. Heat Pump (One Stage with AUX/ K. Heat Pump (Two Stages) Emergency Heat) Thermostat Settings Stage: HP | Type: HG | O/B Type: According Thermostat Settings Stage: HP | Type: HE for electric, HG for gas/oil to previous thermostat setting systems | O/B Type: According to previous Note: G wire is not required.
-
Page 16: Troubleshooting & Support
Stage: HP | Type: HE for electric, HG for gas/oil a paperclip. systems | O/B Type: According to previous thermostat setting Call or email the iDevices Customer Experience Note: G wire is not required. If G wire is not connected, Fan On mode will not be available. ®...