Related Manuals for Zero Z02 Series
Summary of Contents for Zero Z02 Series
- Page 1 Z02 - SWING GATE HOME AUTOMATION zero Z02 - SWING GATE MOTOR HOME AUTOMATION SUPPLY 230-24V IT | EN | FR Z02.REV01.2018 USER MANUAL AND CONFIGURATION...
- Page 2 Z02 - SWING GATE HOME AUTOMATION zero HOME AUTOMATION...
- Page 3 •ZERO SRLS. is not responsible for the improper use of the product, or other use than that for which it was designed.
- Page 4 Z02 - SWING GATE HOME AUTOMATION 02. OPERATOR TECHNICAL SPECIFIATIONS Z02 specifications are as follow: Z02.400 Z02.400.24 Z02.600 Z02.600.24 Power Supply 230Vac 50/60Hz 24Vdc 230Vac 50/60Hz 24Vdc Power 180W 180W Current 1,4 A 1- 3 A 1,4 A 1-3 A Capacitor 8µF...
-
Page 5: Installation Dimensions
Z02 - SWING GATE HOME AUTOMATION 03. INSTALLATION INSTALLATION DIMENSIONS Z02 specifications are as follow: The operator Z02 must be installed with a small inclination , to prevent water infiltration through the extension arm. For this, the front support must be fixed to the gate with a height lower than the height of the rear support. - Page 6 Z02 - SWING GATE HOME AUTOMATION On the Illustrated diagrams below and are the dimensions for the installation of the automated system. Opening mechanic al stopper Opening direction (EXTERIOR) Axis of rotation of theg ate (centero ft he door hinge)
- Page 7 Z02 - SWING GATE HOME AUTOMATION OPENING ANGLE Z02.400 95° 120-180 120-180 1095-1100 120° 160-180 120-140 1095-1100 Z02.600 95° 120-350 120-200 1495-1500 120° 200-280 120-200 1495-1500 Legend: Dimension X - Horizontal distance between hinge axis of the door and the rear axle of the motor.
- Page 8 Z02 - SWING GATE HOME AUTOMATION 03 • Remove caps and pins from motor 04 • Install operator on the supports • Before installing motor, remove caps and • The operator must be placed on both pins from motor.
- Page 9 Z02 - SWING GATE HOME AUTOMATION TIPICAL INSTALLATION • INTERIOR • EXTERIOR • MOTOR • EXTERIOR • KEY • WARNING • ANTENNA • CONTROL PHOTOCELLS PHOTOCELLS PHOTOCELLS SELECTOR LAMP BOARD It is important to use mechanical stoppers in the opening and closing position of the gate.
-
Page 10: Maintenance
Z02 - SWING GATE HOME AUTOMATION 04. MAINTENANCE • Clean stainless steel arm • Lubricate pins • With a cloth soaked in lubricant spray, • Remove front and rear caps wipe any residue that accumulates on the • Place a small amount of lubricant on the operator’s stainless steel arm. - Page 11 Z02 - SWING GATE HOME AUTOMATION 02 • Insert Release key on the unlock 03 • Rotate key 180 ° in the direction indi shaft. cated in the figure to unlock NOTE : To lock operator so it can work automatically, must do it by turning the key anticlockwi-...
-
Page 12: Troubleshooting
Problem Procedure Behavior Procedure II Make sure you have 230V Door doesn’t power supply connected Consult a qualified ZERO work Still not working. to control board and if it technician. is working properly. Consult an experienced Encountered problems? gate expert. - Page 13 All ZERO control boards have LEDs that indicate the functioning of connections to allow easy diagnosis of faults. All safety devices LEDs (DS) in normal situations remain On. All “START” circuits LEDs in normal situations remain Off.
- Page 14 Z02 - SWING GATE HOME AUTOMATION NOTE: _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ _____________________________________________________________________ PG14...
- Page 15 Z02 - SWING GATE HOME AUTOMATION zero HOME AUTOMATION PG15...
-
Page 16: Home Automation
Z02 - SWING GATE HOME AUTOMATION zero HOME AUTOMATION ZERO SRLS Via ROMA 25/A ALTAVILLA VIC. ITALIA info@miozero.it - www.miozero.it PG16...