Subscribe to Our Youtube Channel
Related Manuals for Gude TK 2400 ECO
Summary of Contents for Gude TK 2400 ECO
- Page 1 #55166 TK 2400 ECO English GB 18 Translation of original operating instructions Circular saw bench © Güde GmbH & Co. KG - Birkichstrasse 6 - D-74549 Wolpertshausen - Deutschland...
- Page 2 Unit Mobile bench circular saw with a quality aluminium stop and a plastic mitre cut stop, height readjustment and mitre adjustment by a hand wheel. Accessories (standard): table extension (removable 250 mm) of steel powder colour coated. Dust exhaust, saw disc of sintered metal, sliding guide rod, emergency switch, stop bar with millimetre scale, unit with base.
- Page 3 Guarantee The guarantee exclusively applies to material or manufacturing defects. The original proof of purchase with the purchase date must be submitted when lodging a claim in the guarantee period. The guarantee does not include any unauthorised use, e.g. appliance overloading, violent use, damage by a third party or foreign item.
- Page 4 Product Safety Product compliance with respective EU standards Bans: General ban Do not touch In combination with rotating parts another pictogram) Warning: Beware of Warning/caution hazardous electrical voltage Commands Read operating Use goggles Use ear protectors manual before use Environment Protection Faulty and/or Wastes to be disposed of...
- Page 5 The manufacturer shall not be made liable for damages if general rules and this manual regulations are not observed. Residual Hazards and Protective Action Mechanical Residual Hazards Hazard Description Protective action Residual hazards Cutting, incision Risk of injury caused by rotating Be careful with small pieces to Worn or damaged aids should be parts...
- Page 6 Training Use of the unit requires adequate lesson by a professional or the use of the manual only . Special training is not required. Technical Data TK 2400 ECO Power connection 230 V Frequency/Protection type 50 Hz Max.
- Page 7 Fig. 4 Structural group 4 Delivered parts and Required structural groups accessories Structural group 3 Fig. 1 – pos . 8/8 x Fig. 1 – pos. 9/8 x Fig. 1 – pos . 10/8 x Fig. 1 – pos. 3/4 x Fig.
- Page 8 Fig. 5 Structural group 5 Delivered parts and Required structural groups accessories Structural group 4 Fig. 1 – pos. 12 Fig. 1 – pos. 14 Fig. 1 – pos. 13 Fig. 1 – pos. 15 Fig. 6 Initial Operation Safety Instruction •...
-
Page 9: Operation
• Use only perfect saw discs. I.e. sharpened, without any cracks, fissures, deformations etc. Faulty discs have to be replaced immediately. • Be particular about the arrow on the disc pointing on the same direction as that on the unit. . •... - Page 10 Mitre cut stop • Put the mitre cut stop (Fig. 2/pos. 14) in the respective clamp on the bench. • Release the mitre cut stop (Fig. 2/pos. 14) with the knurled screw . Turn the stop for the arrow to stop at a required angle •...
- Page 11 Lengthwise Cutting • Set the parallel stop (Fig. 2/pos. 3) at the required width in relation to the saw disc. . • Lay the work on the bearing surface are, the flatter/wider side should lay flat on the saw bench. •...
-
Page 12: Troubleshooting
Splitting wedge set-up • Remove the saw disc cover (Fig. 2/pos. Maximum cuts: Distance between the bench and the • Remove the removable part of the bench splitting wedge upper edge 10 cm and loosen both the screws on the approximately . - Page 13 Inspections and Maintenance Unplug the unit before any works on it. • Use a damp cloth to clean plastic parts. Do not use detergents, solvents and pointed things either. • Clean any dirt from the bench surface with a suitable curing compound spray. •...
- Page 14 • Put wrench 13 on the disc spindle . Fig. 22 • Take the belt from the pulley using the screwdriver while turning the disc spindle in the direction of the small pulley. Fig. 23 • Turn until the belt is completely taken off the small pulley . Fig.
- Page 15 • Finished! The saw is in working order again . Fig. 29 Inspection and Maintenance Safety Instructions Only a unit maintained and cared for on a regular basis may be a serviceable aid. Insufficient maintenance and care may result in emergencies and unforeseen accidents.
-
Page 16: Ec Declaration Of Conformity
EC Directive based on its design and type, as brought into circulation by us. In a case of alternation of the machine, not agreed upon by us, this declaration will loose its validity. Machine desciption: - TK 2400 ECO Article-No.: - 55166 Applicable EC Directives: - 2006/42 EC...
Need help?
Do you have a question about the TK 2400 ECO and is the answer not in the manual?
Questions and answers