Sony MO DISK DRIVE SMO-F551 User Manual page 2

Specifications
Operating environment
Installation ±10°
Temperature
Operating 5 °C to 45 °C
(gradient 10° C/h or 18 °F/h)
Relative humidity
Operating 10 % to 90 % (no condensation)
Power supply and others
Power supply +5 V ±5%, 0.8 A (typ.)
+12 V ±5%, 0.9 A (typ.)
Dimensions 41.3 146.0 203.0 mm (H W D)
(without Front Panel)
Weight 1.5 kg
Design and specifications are subject to change without
notice.
Compatible Media
SMO-F551 is compatible with the following 5 1/4 inch
(130 mm) Magneto Optical Disks.
Compatibility Type Description ISO Standard
Read Write
® ®
8 R/W 5.2GB 2048 bytes/sector ISO/IEC 15286
® ®
8 R/W 4.8GB 1024 bytes/sector (working draft)
® ®
8 R/W 4.1GB 512 bytes/sector
® ®
8 WO 5.2GB 2048 bytes/sector
® ®
8 WO 4.8GB 1024 bytes/sector
® ®
8 WO 4.1GB 512 bytes/sector
® ®
4 R/W 2.6GB 1024 bytes/sector ISO/IEC 14517
® ®
4 R/W 2.3GB 512 bytes/sector
® ®
4 WO 2.6GB 1024 bytes/sector
® ®
4 WO 2.3GB 512 bytes/sector
® ®
4 DOW 2.6GB 1024 bytes/sector
® ®
4 DOW 2.3GB 512 bytes/sector
®
2 R/W 1.3GB 1024 bytes/sector ISO/IEC 13549
®
2 R/W 1.2GB 512 bytes/sector
®
2 WO 1.3GB 1024 bytes/sector
®
2 WO 1.2GB 512 bytes/sector
®
1 R/W 650MB 1024 bytes/sector ISO/IEC 10089
®
1 R/W 594MB 512 bytes/sector
®
1 WO 650MB 1024 bytes/sector ISO/IEC 11560
®
1 WO 594MB 512 bytes/sector
W/R : Rewritable, WO : Write-Once, DOW : Direct Overwrite
Configuration and Location of Parts
System Configuration
SMO-F551 is connected to a host computer through its
SCSI interface. The maximum of seven peripheral devices
can be linked as a daisy chain on the SCSI bus.
Host Computer
SCSI Cable
SMO-F551 SCSI peripheral devices
System Configuration Example
Location of Parts
This section provides a general description of the SMO-
F551 Magneto-Optical disk drive.
Front Panel
Disk Insertion Slot
BUSY Indicator Eject Button
Emergency Eject Hole
Front View
Rear Panel
Functional Switch
SCSI Connector
DC Power Connector
GND Terminal
Rear View
SCSI and DC Power Connector
The SCSI and DC Power Connector is located at the upper
rear of the drive. The drive uses a Molex 53450-5431
combination 50 pin SCSI and 4 pin DC Power male header.
Recommended female connectors:
SCSI connector: 3M type number 7950-6500
DC Power connector: AMP 1-480424-0 MATE-N-LOCK
Functional Switch SCSI Connector DC Power Connector
B1 B12
2 50 4 1
A1 A12
1 49
SCSI and DC Power Connector
Switch setting and Assignments
Functional Switch Connector Pin Assignments
A1 SCSI ID2 B1 GND
A2 SCSI ID1 B2 GND
A3 SCSI ID0 B3 GND
A4 Disable SCSI Parity B4 GND
A5 Disable Write Cache B5* Reserved
A6 Disable Auto Spin-up B6* Reserved
A7 Force Verify for Write command B7* Reserved
A8 Disable Manual Eject B8* Reserved
A9 Enable Fast SCSI B9* Reserved
A10 Device Type B10* Reserved
A11 Enable Termination B11 GND
A12 Terminator Power B12 Terminator Power Source
* This pin is NOT directly connected to the GND. Do not use this pin as
GND. SMO-F551 drives the signal to GND level depending on the
functional switch setting. Otherwise, the signal is not driven to GND
level.
WARNING: Write cache is enabled as default
setting. The integrity of the buffer memory content
is not guaranteed through power cycling.
Caution: "Disable Write Cache" setting works as an "OR"
function with the optional dip switch setting.
Caution: When the Fast SCSI function is used, it is
recommended that the host system and SCSI cables should
conform to the Fast SCSI.
DC Power Connector Pin Assignments
Pin Number Description
1 DC +12V
2 +12V Return
3 +5V Return
4 DC +5V
Pin Assignments of SCSI Connector
Signal Name Pin No. Signal Name
GND 1 2 DB0
GND 3 4 DB1
GND 5 6 DB2
GND 7 8 DB3
GND 9 10 DB4
GND 11 12 DB5
GND 13 14 DB6
GND 15 16 DB7
GND 17 18 DBP
GND 19 20 GND
GND 21 22 GND
GND 23 24 GND
OPEN 25 26 (TERM PW)
GND 27 28 GND
GND 29 30 GND
GND 31 32 ATN
GND 33 34 GND
GND 35 36 BSY
GND 37 38 ACK
GND 39 40 RST
GND 41 42 MSG
GND 43 44 SEL
GND 45 46 C/D
GND 47 48 REQ
GND 49 50 I/O
The bar "—" above the signal indicates active low.
SCSI Terminator
SMO-F551 features an internal SCSI bus terminator. When
the drive is connected at the end of the SCSI chain,
functional switch #11 (Enable Terminator) may be used to
terminated the SCSI connection.
For a single ended cable, 50-signal conductor flat cable or a
25-signal twisted cable can be used. The cable length shall
not exceed six meters.
Optional Switch Setting
SMO-F551 features Optional Switch S501 and S502.
These two optional dip switches allow the user to set the
drive configurations.
Top Panel View
Optional Dip Switch Assignments
Optional Switch Description
Switch Number
1 Reserved
2 Reserved
3 Disable Command Eject
S501 4 Reserved
5 Reserved
6 Reserved
7 Disable Write Cache
8 Disable Auto Spin-up
1 Reserved
2 Reserved
3 Reserved
S502 4 Reserved
5 Disable SCAM Selection
6 Reserved
7 Reserved
8 Enable Write Cache for Write and Verify Command