Wire Connection Guide For Passlock Ii; Passlock Ii Wiring Diagram; Passlock Ii Programming - Directed Electronics 556L Manual

N N O O T T E E : : Refer to the end of this document for
troubleshooting procedures.
W W i i r r e e C C o o n n n n e e c c t t i i o o n n G G u u i i d d e e f f o o r r P P a a s s s s l l o o c c k k I I I I
G G R R E E E E N N / / B B L L A A C C K K : : Not used for this application.
B B L L A A C C K K / / W W H H I I T T E E : : Not used for this application.
B B L L A A C C K K ( ( - - ) ) P P a a s s s s l l o o c c k k g g r r o o u u n n d d i i n n p p u u t t : : Connect this input to the
Passlock system's ground reference wire.
P P I I N N K K ( ( + + ) ) i i g g n n i i t t i i o o n n i i n n p p u u t t : : Connect this wire to the heavy gauge pos-
itive (+) PINK wire of the vehicle's main ignition.
B B L L U U E E ( ( - - ) ) s s t t a a t t u u s s i i n n p p u u t t : : Connect this wire to the (-) status output
(BLUE/WHITE or BLUE) of the Directed remote start system.
P P a a s s s s l l o o c c k k I I I I W W i i r r i i n n g g D D i i a a g g r r a a m m
GREEN/BLACK—(not used)
BLACK/WHITE—(not used)
BLACK—Passlock ground
HARNESS 1 PINK—(+) ignition input
BLUE—(-) status input
VIOLET—(not used)
RED—(+) 12V
WHITE—(not used)
YELLOW—key side resistance in
HARNESS 2
WHITE/YELLOW—(not used)
BLACK/YELLOW—vehicle side resistance out
P P a a s s s s l l o o c c k k I I I I P P r r o o g g r r a a m m m m i i n n g g
The module must first be programmed before operation, use the
following procedure:
I I M M P P O O R R T T A A N N T T ! ! The vehicle must be started within 15
seconds or the module will automatically exit the learn
routine.
1. Cycle the ignition On/Off 2 times.
2. Start the vehicle and keep it running for at least 10-seconds.
3. The LED on the module will flash 2-times.
© 2005 Directed Electronics, Inc. Vista, CA
N556L 05-05
V V I I O O L L E E T T ( ( - - ) ) : : Not used for this application.
R R E E D D ( ( + + ) ) 1 1 2 2 v v o o l l t t i i n n p p u u t t : : Connect this wire to a fused source of con-
stant 12 volts.
W W H H I I T T E E : : Not used for this application.
Y Y E E L L L L O O W W R R - - C C o o d d e e , , i i g g n n i i t t i i o o n n s s w w i i t t c c h h : : Connect this wire to the ignition
switch side of the Passlock II system's cut resistance wire.
W W H H I I T T E E / / Y Y E E L L L L O O W W : : No connection.
B B L L A A C C K K / / Y Y E E L L L L O O W W R R - - C C o o d d e e , , o o u u t t p p u u t t t t o o v v e e h h i i c c l l e e s s i i d d e e : : Connect this wire
to the side of the resistance wire facing away from the ignition
switch.
4. Wait for the LED to flash once very quickly (within 5-seconds)
of ignition On. The R-code is learned.
3. Programming is now complete. Turn the vehicle's ignition off
and test remote start at least twice.
N N O O T T E E : : Refer to the end of this document for
troubleshooting procedures.
3 3