Advertisement
Available are over 8,000 different programmable settings which are available in either receiver.
Questions on programming should be directed to Technical Support @ 888-392-2007 x 1751.
2. Hold the receiver close to the edge of the transmitter
board....find the "Sweet Spot". The receiver's
battery light comes on to indicate the receiver is
ready to be programmed.
NOTE: Should the receiver signal a solid tone and
the light stays on this means that the receiver did
not detect the transmitter's signal correctly. When
the beep stops repeat Step 2.
3. Increase Training Correction Level - To increase
the Training Correction Level, press the top black
button. The receiver will beep twice to indicate an
increase in the correction level and the low battery
light flashes to indicate the training level the receiver
is set on. You can only increase the correction level
by 1 increment at a time. To increase the level more
than one increment you must go back to the
beginning of Step 4 and start over.
If you try to increase the correction level once
you have reached 89 the receiver will rapidly
beep for approximately 2 seconds to indicate that
the correction level is at its highest level (89).
NOTE: Correction Level 88 is equivalent to
correction level 31 and Correction Level 89 is
equivalent to correction level 33.
Decrease Training Correction Level - To decrease
the Training Correction Level, press the bottom
black button. The receiver will beep once to indicate
a decrease in the correction level and the low
battery light flashes to indicate the training level the
receiver is set on. You can only decrease the
correction level by 1 increment at a time. To
decrease the level more than one increment you
must go back to the beginning of Step 4 and start
over.
If you try to decease the correction level when
the level is set to 81 the receiver will rapidly
beep for approximately 2 seconds to indicate
that the Correction Level is at its lowest setting
(81).
NOTE: If the receiver sounds a solid tone and
the light stays on this means that the code is
not compatible with the receiver and will not be
successfully transmitted to the receiver.
©2008 Perimeter Technologies, Inc.
Underground Dog Fence
Pet Stop of North Georgia, LLC
Programming Guide – OT-200
4. After reprogramming is complete the transmitter returns
to normal operation. You can also return to normal
operation by unplugging the power cord, waiting 5
seconds, and then reinserting the power cord.
Alternatively, do nothing for two minutes and the
transmitter will return to normal operation.
Step 5 – Adjust Distance (This adjustment gives the
ability to change where the Receiver activates either
farther from or closer to the Boundary Wire)
1. While in normal operation mode press and hold the
Distance Button on the transmitter until the display
begins to flash "97".
2. Hold the receiver close to the edge of the transmitter
board. The receiver's battery light comes on to indicate
the receiver is ready to be programmed.
NOTE: Should the receiver signal a solid tone and
the light stays on this means that the receiver did
not detect the transmitter's signal correctly. When
the beep stops repeat Step 2.
3. Increase Distance - To increase the Distance, press
the top black button. The receiver will beep twice to
indicate an increase in sensitivity. Increasing Distance
makes the receiver activate farther from the boundary
wire. You can only increase Distance by 1 increment at
a time. To increase Distance more than one increment
you must go back to the beginning of Step 5 and start
over.
Once the receiver has been adjusted to its
maximum Distance and you try to increase
Distance the receiver will rapidly beep for
approximately 2 seconds to indicate that the
Distance is set to maximum.
Decrease Distance - To decrease the Distance,
press the bottom black button. The receiver will beep
once to indicate a decrease in Distance. Decreasing
Distance makes the receiver activate closer to the
boundary wire. You can only decrease the Distance
by 1 increment at a time. To decrease the Distance
more than one increment you must go back to the
beginning of Step 5 and start over.
Once the receiver has been adjusted to its minimum
Distance and you try to decrease it further the
receiver will rapidly beep for approximately 2
seconds to indicate that the Distance is set to
minimum.
Advertisement
