Philips 32PFL5405H/05 Service Manual page 43

Table 6-9 Option and display code overview
CTN Options Group 1
(Alt. BOM#)
32PFL5405H/xx 00008 00000 15421 02176 43798 34315 00000 00000 278
32PFL5605H/xx 00008 00000 15421 08192 44009 34315 00000 00000 233
32PFL7605H/xx 02060 00000 12351 30911 43795 34315 00000 00000 275
37PFL5405H/xx 00008 00000 15421 02176 43798 34315 00000 00000 278
40PFL5605H/xx 00008 00000 15421 08192 44009 34315 00000 00000 233
40PFL7605H/xx 02060 00000 12351 30911 43795 34315 00000 00000 275
42PFL5405H/xx 00008 00000 15421 02176 43798 34315 00000 00000 278
Important: after having edited the option numbers as
described above, you must press OK on the remote control
before the cursor is moved to the left!
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool.
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this (new in this platform), you can use the NVM editor in
SAM. This action also ensures the correct functioning of the
"Net TV" feature and access to the Net TV portals. The loading
of the CTN and production code can also be done via ComPair
(Model number programming).
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
6.5.1 SSB identification
Whenever ordering a new SSB, it should be noted that the
correct ordering number (12nc) of a SSB is located on a sticker
on the SSB. The format is <12nc SSB><serial number>. The
ordering number of a "Service" SSB is the same as the ordering
number of an initial "factory" SSB.
Figure 6-1 SSB identification
Options Group 2 Disp.
code
18310_221_090318.eps
090319
back to
div. table
Alignments Q552.1E LA
6.6 Service SSB delivered without main software
loaded
Due to a changed manufacturing process, new Service SSB's
can be delivered to the warehouse without main TV
software loaded. Below you find the steps to follow when such
an SSB is received.
6.6.1 When a picture is available
1. Mount the Service SSB into the TV set. After start-up,
normally the download application will appear on the
screen.
2. Download the latest main software (FUS) from the
www.p4c.philips.com
3. Create a folder "upgrades" in the root of a USB stick (size
> 50 MB) and save the "autorun.upg" file in this "upgrades"
folder. Note: it is possible to rename this file, e.g.
"Q555_SW_version.upg", this in case there are more than
one "autorun.upg" files on your USB stick
4. Plug the prepared USB stick into the TV set, and select the
"autorun" file in the displayed browser on the screen
5. Now the main TV software will be loaded automatically,
supported by a progress bar
6. Set the correct "display code" via "062598-HOME-xxx",
where "xxx" is the 3-digit display panel code (see sticker on
the side/bottom of the cabinet).
6.6.2 When no picture is available
Due to a possible wrong display option code in the received
Service SSB (NVM), no picture can be available at start-up and
thus no download application will be visible. Here you can
proceed and finalize step by step to load the main TV software
via the UART logging on the PC (for visual feedback).
1. Start-up the TV set, equipped with the Service SSB, and
enable the UART logging on the PC (see for settings
Fault Finding and Repair Tips 5.8.6
2. The TV set will start-up automatically in the download
application if main TV software is not loaded
3. Plug the prepared USB stick into the TV set, press cursor
"Right" to enter the list, and navigate to the "autorun" file in
the UART logging printout via the cursor keys on the
remote control. When the correct file is selected, press
"OK"
4. Press cursor "Down" and "OK" to start the flashing of the
main TV software. Printouts like: "L: 1-100%, V: 1-100%
and P: 1-100%" should be visible now in the UART logging
5. Wait until the message "Operation successful!" is displayed
and remove all inserted media. Restart the TV set
6. Set the correct "display code" via "062598-HOME-xxx",
where "xxx" is the 3-digit display panel code (see sticker on
the side/bottom of the cabinet).
6.6.3 Use of repaired SSBs instead of new
Repaired SSBs on stock will obviously already contain main TV
software. This implies that only a main software upgrade is
required if you use a "repaired" SSB for board swap instead of
a "new" SSB.
6. EN 43
website.
Logging)
2010-Feb-19
5.8