Input Impedance Check; Alignment And Calibration Procedures; Alternate Accuracy And Frequency Response Check Setup - HP 400F Operating And Service Manual

ModeI 400F/FL
OSCILLATOR
hp
200SR
FREQUENCY RESPONSE
TEST SET
hp
739AR
VOLTMETER CALIBRATOR
hp
73.BR
__ ._f"" _
Figure 5-2.
Set 400F/FL RANGE switch to 100 my.
d_
400F should indicate 30 mv ±2%.
1)
2) 400FL should indicate 30 mv ±1%.
Set 400F/FL RANGE switch to O. 3 volts.
e.
1) 400F should indicate 30 mv ±5%.
2) 400FL cannot be checked with a
scale input.
!.
Adjust test oscillator (or a 400F/FL meter
indication of 30 mv at 1 MHz.
g. Set 400F/FL RANGE switch to 100 mv.
1)
400F should indicate 30 mv ±2%.
2) 400FL should indicate 30 mv :1%.
h. Set 400F/FL RANGE switch to O. 3 volts.
400F should indicate 30 mv :5%.
1)
2) 400F/FL cannot be checked with a 1/10
scale input.
5-16. INPUT IMPEDANC E CHECK.
5-17. INPUT RESISTANCE CHECK.
0
a. Connect the 50
to 400F/FL.
b. Set 400F/FL RANGE switch to
c. Set test oscillator output for full scale deflec­
tion of 400 F / FL.
d. Connect a 100 K
cillator and 400F/FLas shown in Figure 5-3.
01795-1
VTVM CALIBRATION SYSTEM
hp
K02 - 73eBR
@
@
@
� O
0

Alternate Accuracy and Frequency Response Check Setup

1/10
of
output the test oscillator
1
volt_
n
resistor between test os­
Paragraphs
[9 0
IQ)
0
o Q ®
e. 400F/FL meter indication should not drop
more than one small scale division from full
scale.
O.
10 M
5-18. INPUT CAPACITY CHECK.
Connect test oscillator and a 100 K
a.
t0400F/FL as shown in Figure 5-3.
the resistor lead directly to the GR connector.
b.
Set 400F/FL RANGE switch to
c. Set test oscillator output for full scale deflec­
tion of 400F/FL meter at 400 Hz.
d. Increase frequency of test osclllator until
400F/FL indication drops toO. 707 volts.
should occur at a frequency
greater. verifying an input capactty of
less on the
e. Set 400F/FL RANGE switch to 300 my . .
!.
Set frequency response test set output for full
scale deflection
g. Increase frequency of test oscillator until
400F/FL indication drops to
should occur at a frequency of 60 KHz or
greater, verifylngan Input capacity of
less on the 300 mv range.
5-19. A L I G N M E N T A N D C A L I B R AT I O N
P R O C E D U R E S .
5-20. The Alignment and Calibration Procedures should
be performed only if it has been determined by the
Performance Checks that the 400F/FL is not within
5-16
to 5-20 and Figure 5-2
hp
400F/FL
AC VOLTMETE
"
, -,
I
I
L _ -l
This verifies an input resistance
1
of
1
volt range.
of
400F/FL meter at 400 Hz.
212
Section V
R
of
0
resistor
Connect
volt.
This
150 KHz or
pf
1
0 or
my. This
25 pr or
5-3