Advertisement
Quick Links
VARIPUMP12811181MAN
UK
English
INSTRUCTION MANUAL
PLEASE READ all of the instruction manual before attempting
to install or operate the Varipump
Evolution Aqua Ltd. - Evolution House - Kellet Close - Wigan - Lancashire - United Kingdom - WN5 0LP
t +44 (0) 1942 216554 - f +44 (0) 1942 418 489 - e info@evolutionaqua.com - w www.evolutionaqua.com
Advertisement
Related Manuals for Evolution Aqua Varipump 10000
Summary of Contents for Evolution Aqua Varipump 10000
- Page 1 Varipump Evolution Aqua Ltd. - Evolution House - Kellet Close - Wigan - Lancashire - United Kingdom - WN5 0LP t +44 (0) 1942 216554 - f +44 (0) 1942 418 489 - e info@evolutionaqua.com - w www.evolutionaqua.com...
-
Page 2: Important Safety Information
WARNING: PLEASE READ THE FOLLOWING SAFETY INFORMATION FIRST. IMPORTANT SAFETY INFORMATION - Please read the instruction manual carefully. - The electrical installation is to be done by a qualified electrician, in accordance with applicable electrical codes. - WARNING: Always shut off electrical power before installation and / or servicing this pump. - Page 3 INTRODUCING THE EVOLUTION AQUA VARIPUMP Congratulations on purchasing an Evolution Aqua Varipump. Varipump by Evolution Aqua is a controllable pond pump, suitable for large ponds. Output and energy consumption can be controlled at the push of a button and the six pole, three phase motor is quiet and reliable.
-
Page 4: Specifications
DIMENSIONS DIMENSIONS 267mm (L) x 122mm (W) x 162mm (H) Varipump 10000 319mm (L) x 142mm (W) x 181mm (H) Varipump 20000 370mm (L) x 155mm (W) x 205mm (H) Varipump 30000 SPECIFICATIONS MAX. MAX. MAX. FLOW FLOW FLOW MAX. - Page 5 When installing in gravity fed systems ensure unions are fitted (not supplied) to enable removal of the pump for cleaning and maintenance. We recommend using Evolution Aqua unions (EA CODE: K82-76-55) for the 10,000 model. Use unions (EA CODE: K82-76-66) for the 20,000 and 30,000 models.
- Page 6 INSTALLING THE VARIPUMP - PUMP FED Varipump can be submersed in water, as part of a pump fed system. When installing on pump fed systems ensure we recommend using the hosetails provided to connect up to flexible hose (not supplied). 1.
-
Page 7: Operating Temperature
OPERATING TEMPERATURE The permissible temperature is > than 0˚C and < than 35˚C. The pump should never be operated outside of these temperatures or damage may occur. STARTING UP THE VARIPUMP Your varipump is supplied with an in-line digital controller. If wired correctly the pump will switch on as soon as it is plugged in. - Page 8 CLEANING THE VARIPUMP Step 1: Hold pump by the handle and remove the inlet strainer basket Step 2: Using a Phillips screwdriver, undo the four screws at the base of the pump body Step 3: Remove the volute Step 4: Clean any debris and algae from inside the volute using a brush Step 5: Pull the impeller out of the housing by hand Step 6: Clean the impeller with a bush.
- Page 9 CLEANING THE VARIPUMP Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8...
-
Page 10: Troubleshooting
TROUBLESHOOTING Symptom Problem Resolution Insufficient Prime Prime system with water and purge all air from suction piping. Wired incorrectly or an RCD has tripped. No Power Pump has been switched off at the controller. Ensure valves are open. Ensure plumbing is clear, including suction strainers, No Flow check valves, etc. - Page 11 Any warranty claim must be accompanied by a valid, dated proof of purchase. Evolution Aqua, its distributors and dealers shall not be held liable for any loss of fish, plants or any other livestock as a result of any failure or defect of this product.
- Page 12 Evolution Aqua Ltd Evolution House, Kellet Close Wigan, Lancashire, United Kingdom WN5 0LP t: +44 (0) 1942 216554 f: +44 (0) 1942 418489 e: info@evolutionaqua.com w: www.evolutionaqua.com...