Leer SR 250 Installation Instructions & Owner's Manual

Leer SR 250 Installation Instructions & Owner's Manual

With exclusive cync latching system

Advertisement

WITH LEER'S EXCLUSIVE
INSTALLATION INSTRUCTIONS &
Thank you for purchasing the LEER
make it better, front to back and inside out. We engineered components with new innovations at every
point including our CYNC™ latching system (patented). The result is a soft rolling cover that's unlike any
cover on the road today.
NOTICE TO INSTALLER: It is recommended you take time to read these instructions before installing the
cover even if already familiar with the product. Improvements are often made without prior notice. Al-
ways handle the cover and components with care to avoid damage. If you find a part missing or defective,
or if you have trouble installing this product, please have the model number ready (located on a tag under
the first panel) and call your dealer. When done, these instructions and warranty information must be giv-
en to the customer to keep.
NOTICE TO CUSTOMER: Before using this product, read the operating instructions, maintenance and
safety sections of this owner's manual and save for future reference. Your new LEER tonneau must be
registered to make the warranty valid. Registration information can be found on the back page.
FOR YOUR RECORDS
Patented and Patent Pending see LEER.com
OWNER'S MANUAL
SR 250 soft rolling tonneau cover. At LEER, we looked at ways to
R
DATE PURCHASED:___________________________________
SERIAL NUMBER:_____________________________________
LEER RETAILER:______________________________________
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SR 250 and is the answer not in the manual?

Questions and answers

Summary of Contents for Leer SR 250

  • Page 1 NOTICE TO CUSTOMER: Before using this product, read the operating instructions, maintenance and safety sections of this owner’s manual and save for future reference. Your new LEER tonneau must be registered to make the warranty valid. Registration information can be found on the back page.
  • Page 2: Table Of Contents

    - 6 EACH CLAMP ASSEMBLY (STYLE VARIES PER CLAMP KIT) - 2 EACH FRONT CROSSBAR HOLD DOWN - 1 EACH 2.5MM ALLEN WRENCH - 1 EACH 5MM ALLEN WRENCH - 1 EACH 6MM ALLEN WRENCH TOOLS INCLUDED Patented and Patent Pending see LEER.com...
  • Page 3: Pre-Preparation

    LOWER SCREW STEP 2: TIGHTEN CLAMP SCREWS USING 5 MM ALLEN AS SHOWN. ONCE TIGHTENED YOU MAY REMOVE LOWER SCREWS, RETAIN THEM IF LATER ADJUSTMENTS ARE NEEDED. CLAMP SCREW (REPEAT STEPS FOR RIGHT HAND SIDE) Patented and Patent Pending see LEER.com...
  • Page 4 PLACE FRONT CROSS BAR BOLTS INSIDE RAIL SLOTS AS SHOWN ABOVE. LINE UP COVER ASSEMBLY ON FOURTH TOOTH AS SHOWN BELOW. FRONT SHIELD SHOULD BE PULLED OUT. SEE ABOVE FOR FASTENER ASSEMBLY SEQUENCE. * REPEAT FOR OPPOSITE SIDE Patented and Patent Pending see LEER.com...
  • Page 5 FOLD DOWN THE COVER AS SHOWN FOR CYNC LATCH ENGAGMENT. ADJUSTING FOR TAUTNESS OF COVER (IF NEEDED) LOOSEN COVER TIGHTEN COVER (MOVE OVER TEETH (MOVE OVER TEETH TOWARD REAR TAIL GATE) TOWARD FRONT OF BED) Patented and Patent Pending see LEER.com...
  • Page 6: Replacement Parts

    QUANTITY ITEM NUMBER QTY ORDERED LEER SR250 CLAMP KITS 1 EACH FRONT PART KIT 1 EACH 208388 CYNC LATCH KIT 1 EACH 209037 REAR LOCK KIT 1 EACH 208389 RAIL SEAL KIT 1 EACH Patented and Patent Pending see LEER.com...
  • Page 7 - 1 EACH FRONT PART KIT #206660 #206661 FRONT PART KIT #208930 #208933 #208940 #208388 RAIL SEAL KITS (INCLUDES BULKHEAD SEAL) CYNC LATCH KIT REAR LOCK KIT #209043 #209038 #209039 #209040 #209041 #209042 #208389 #209037 Patented and Patent Pending see LEER.com...
  • Page 8: Warranty Policy

    SR250 is an important step to ensuring you get the best possible ownership experience. At the same time, we would like to better understand how your truck fits into your life. Feedback from LEER owners helps us design products that better fit your needs.

Table of Contents