Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Lawn Solutions Turf Revitalizer
Summary of Contents for Lawn Solutions Turf Revitalizer
- Page 1 Turf Revitalizer 6 - 14hp Owner’s Manual...
-
Page 2: Table Of Contents
CONTENTS Page# Safety……………………..……….…..3 Unpacking and Initial setup…..….…4-5 Controls..……………………………6-8 Operation……………………….….9-10 For Best results………….………..10-11 Servicing your Turf Revitalizer….12-16 Storage………………………………16 Troubleshooting……………………..17 Warranty……………………………..18 Parts Breakdown………...…………..19 - 2 -... -
Page 3: Safety
Safety Do not start and/or run engine indoors. Engine produces carbon monoxide and can cause severe bodily harm, including death. Read entire owner’s manual before operation. Do not refuel engine until engine has cooled off. The exhaust becomes very hot during operation. Never touch the muffler as this will cause severe burns. -
Page 4: Unpacking And Initial Setup
Unpacking and Initial Setup Unpacking Step1. Cut away crate. o Use a reciprocating saw to cut away wooden crate. Step2. Fold Handles up. (Note: On the 13-14HP units this task takes two people.) o Units are shipped with the handle folded in the down position. - Page 5 Initial Setup Step1. Top the engine off with oil. o Units are shipped with some oil. Engine should be topped off with the correct oil viscosity. See engine manual for the correct oil viscosity. Step2. Adjust the transmission cable. (Note: On the 13-14HP units the blade engagement cable will need to be installed at handle;...
-
Page 6: Controls
Controls Cutter Blades ON / OFF Seed Flow ON / OFF Pistol Grip Transmission Control Note: Seed Flow – the seed flow is turned on/off with the seed flow control. The unit is designed so seed flow slows or almost stops completely when the front wheels are off the ground while making turns. - Page 7 Pistol Grip Control- the unit is operated (forward and backward) using a pistol grip control, like those found on a commercial walk behind mower. Disengage the lever, with your thumb, from the “park” position and release slowly to move forward (Note: 9-14 HP units have two forward cruising speeds).
-
Page 8: Controls
Seed Meter Gauge – The “Seed Meter Gauge” is used to adjust the seed flow to a set flow rate. It is calibrated so that you receive the correct amount of seed at any cruising speed. (i.e. – the seed flow is proportional to the ground speed)See figure 7. -
Page 9: Operation
Operation Before each day of use. o Check engine oil level and air filter. o Check for loose or damaged parts. o Clean dirt and debris from seed gate by turning seed flow setting (seed meter gauge) to #10, then turn the seed flow on. -
Page 10: For Best Results
Figure 3. For Best Results The Turf Revitalizer is a 3 in 1 machine that will power seed, dethatch, and power rake. Power Seeding – When over seeding, set the blades to cut slits in the soil ¼”... - Page 11 This will prevent the new grass from suffocating under the thatch. Note: With the Turf Revitalizer, it is very easy to put more grass seed down then is recommended because of the thinking that “more is better”.
-
Page 12: Servicing Your Turf Revitalizer
Servicing your Turf Revitalizer The Turf Revitalizer is designed to be relatively maintenance free. For long life and to reduce down time some routine service should be performed. Note: Always disconnect the sparkplug before servicing. After each day of use: ... -
Page 13: Operation
o Procedure for adjusting “cutter reel” belt tension. 1. Remove the belt cover. 2. Turn on Cutter Reel. 3. With the engine off and the blades in the up position, press forward on the belt tensioner. The belt should be tight and the “cutter cable”... - Page 14 o Procedure for adjusting transmission belt tension. 1. Remove the belt cover. 2. Loosen all four nuts shown in figure 11. 3. Slide idler bracket away from engine to increase tension. If movement cannot be obtained insert four c-washers in between the idler bracket and the frame, see figure 12.
- Page 15 Change engine oil at the recommend intervals. Refer to your engine manual for these intervals and correct viscosities. There is no maintenance to the hydrostatic drive system. It is designed to be completely sealed to prevent contamination. The blades are designed to be “unbreakable”. When replacing worn blades, it is also recommended to change the cutter bearings while they are off the unit as preventative maintenance.
-
Page 16: Storage
Antiseize shaft! TL, Set Screws Figure 13. “TL”-Thread Lock. Seed gate cable adjustment. 1. Set seed flow to off position. 2. Check for any gaps in between the seed gate and frame. 3. Make any needed adjustments to the seed gate cable if needed. Do not adjust the cable where there is excessive tension placed on the cable due to pulling the seed gate past the limit of travel. -
Page 17: Troubleshooting
Troubleshooting Problem Possible Cause Correction Out of gas. Fill gas. Engine will not Low Oil. Top off oil. start. Kill switch. Hold down OP handle or attach lanyard. Engine shutting off Engine is low on oil. Top engine off with on hills or when Oil switch is detecting oil. -
Page 18: Warranty
Lawn Solutions will replace for the original purchaser free of charge any part or parts found to be defective in material or workmanship. Lawn Solutions may require the defective parts to be returned for further examination. Due to the ease of maintenance on the product, this is a parts only warranty. -
Page 19: Parts Breakdown
Control Panel ASM - 19 -... - Page 20 Front Parts View Side Parts View - 20 -...
- Page 21 Top Parts View - 21 -...
- Page 22 - 22 -...
- Page 23 9-hp Reel ASM - 23 -...
- Page 24 6-hp Reel ASM - 24 -...
- Page 25 Ring Terminal 22-18ga wire w/ 5/16" Stud LS0127 Butt Splice 22018ga wire LS0128 Small Black Wire Ties LS0038 Decal Set - Turf Revitalizer LS0038B Decal Seed Flow Graph - TR LS0097 Toe Guard - 6hp LS0098 Toe Guard - 9hp...
- Page 26 Service Parts List Part Item Descriptions Number LS0001 Cutter Shaft 18" Fits Model (TR2060xxx1) LS0001a 1a Cutter Shaft 20" Fits Model (TR2090xxx1) 1b Cutter Shaft 24” Fits Model (TR2414xxx1) LS0001b 1c Cutter Shaft 30” Fits Model (TR3014xxx1) LS0001c LS0002 Retaining Ring - 1" Heavy Duty LS0003 Cutter Blade (.120") LS0004...
- Page 27 Handle) LS0036 36 Lanyard Kill Switch LS0037 37 Lanyard LS0038 38 Decal Set - Turf Revitalizer LS0038B 38B Decal Seed Flow Graph - TR LS0039 39 Belt - Transmission (6-hp) LS0040 40 Belt - Transmission (9-hp) LS0040b 40b Belt – Transmission TR24...
- Page 28 LS0040c 40c Belt – Transmission TR30 LS0041 41 Belt - Cutter Blades (6-hp) LS0042 42 Belt - Cutter Blades (9-hp) LS0042a 42a Belt – Cutter Blades TR24 & TR30 LS0043 43 Transmission LS0043b 43b Transmission TR24 LS0043c 43c Transmission TR30 LS0044 44 Tire 4.10 / 3.50 - 4 (6hp) LS0045...
- Page 29 LS0065 65 Engine - 13.5 HP LS0066 66 Carriage Bolt 5/16-18 x 5/8" LS0069 69 Frame ASM - TR20" Handle Extensions - TR20xxxxA1-TR20xxxxB1 (Some earlier TR20xxxxC1 LS0070 have this handle) (Flat Steel) LS0070a 70a Folding Handle Extensions TR20xxxxC1-TR20xxxxD1 (Round Tube) 71 20”...
- Page 30 LS0083 83 Finger Guard TR20 LS0083b 83b Finger Guard TR24 & TR30 LS0084 84 Spacer 5/8" x 0.480 LS0085 85 Spacer 5/8" x 2.25 LS0086 86 Seed Flow Dial LS0088 88 Trans Mount Bracket LS0088a 88a Transmission Mount Frame Side TR24 & TR30 LS0088b 88b Transmission Mount Center TR24 &...
- Page 31 LS0110 110 Spring Pin 1/4" x 1" Steel LS0111 111 Cable Clip 1/4" LS0112 112 Carriage Bolt 1/4-20 x 1 1/4"" LS0113 1113 Carriage Bolt 1/4-20 x 1" LS0114 114 Carriage Bolt 5/16-18 x 3/4" LS0115 115 Carriage Bot 5/16-18 x 1" LS0118 118 Button Head Cap Screw 1/4-20 x 1"...
- Page 32 OP Handle) OP Kill Switch – connector (For use with models that use a Red Plastic OP LS0143 Handle) OP Kill Switch - Switch only (For use with models that use a Red Plastic LS0144 OP Handle) LS0148 148 Hopper Cover Latch LS0149 149 Trans Torq Bracket LS0150...
Need help?
Do you have a question about the Turf Revitalizer and is the answer not in the manual?
Questions and answers