Advertisement
Quick Links
183 RANGE PRESSURE FEED TANKS with and without
AGITATION, 9.5, 40 and 60 Litre capacities
Tank Model
183S-210-CE
183S-211-CE
183S-212-CE
183S-213-CE
183S-1010-CE
183S-1012-CE
183S-1013-CE
183G-1010-CE
183G-1012-CE
183G-1013-CE
183S-1510-CE
183S-1512-CE
183S-1513-CE
Important: Read and follow all instructions and SAFETY
PRECAUTIONS before using this equipment. Retain for future
reference.
DESCRIPTION
These Pressure Tanks are CE marked in accordance with the
Pressure Equipment Directive 97/23/EC and ATEX Directive
94/9/EC Cat 2 G X for use in Zones 1 and 2. The agitators used
in the agitated models are ATEX certified to Cat 1/2 Gc T4.
They are suitable for use with flammable materials. 183S
models are suitable for use with water based and more
corrosive materials.
These pressure tanks are designed as a pressure container to
supply liquid material at a constant preset pressure up to a
maximum of 7.6 bar (110 psi). The tanks are built to ASME BPV
XIII standards. 183G models are constructed from Galvanised
carbon steel. 183S models are constructed from stainless steel. A
polyethylene liner is included for easy clean up.
Capacity
Material Type
9.5 litre
Stainless Steel
9.5 litre
Stainless Steel
9.5 Litre
Stainless Steel
9.5 Litre
Stainless Steel
40 litre
Stainless Steel
40 litre
Stainless Steel
40 litre
Stainless Steel
40 litre
Galvanised Steel
40 litre
Galvanised Steel
40 litre
Galvanised Steel
60 litre
Stainless Steel
60 litre
Stainless Steel
60 litre
Stainless Steel
Agitation
None
Direct Drive
Manual
Gear-reduced (Heavy-duty)
None
Manual
Gear-reduced (Heavy-duty)
None
Manual
Gear-reduced (Heavy-duty)
None
Manual
Gear-reduced (Heavy-duty)
Part Sheet
77-2931/2
EN
Advertisement
Related Manuals for Binks 183S-211-CE
Summary of Contents for Binks 183S-211-CE
- Page 1 183S models are constructed from stainless steel. A polyethylene liner is included for easy clean up. Tank Model Capacity Material Type Agitation 183S-210-CE 9.5 litre Stainless Steel None 183S-211-CE 9.5 litre Stainless Steel Direct Drive 183S-212-CE 9.5 Litre Stainless Steel Manual 183S-213-CE 9.5 Litre...
- Page 2 IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT. FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300). © ITW FINISHING SYSTEMS AND PRODUCTS...
-
Page 3: Pressure Relief Procedure
The following hazards may occur during the normal use of this equipment. Please read the following chart before using the equipment. HAZARD CAUSE SAFEGUARDS Fire Solvents and coatings can be highly flammable Adequate exhaust must be provided to keep the air free or combustible, especially when sprayed. -
Page 4: Specifications
SPECIFICATIONS 183G GALVANIZED TANKS 183S STAINLESS STEEL TANKS Maximum Working Pressure 110 psi Tank Shell SA-414 Steel, Galvanized (Zinc) 304 Stainless Steel Tank Lid SA-414 Steel, Galvanized (Zinc) 304 Stainless Steel Fluid Tube 3/8 in. Steel Pipe, Galvanized 3/8 in. SS Pipe, 316 Stainless Steel Fluid Outlet (Elbow) Steel, Zinc Plate 316 Stainless Steel... -
Page 5: Installation
charges. Check continuity to earth before start the agitator by slowly opening up the WARNING using the equipment. needle valve. Air motor speed should be regulated according to the nature of the High pressure can cause serious injury. LUBRICATION – Agitated material being agitated. - Page 6 Air mixing with paint Fluid tube not sealed to lid. Tighten fluid tube into lid. Excessive agitation. Reduce speed of agitator. FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300). © ITW FINISHING SYSTEMS AND PRODUCTS...
- Page 7 183S RANGE - 9.5 LITRE TANK ASSEMBLIES Note Use PTFE based thread sealant on all air and fluid connections For regulator parts see page 13 PETROLEUM JELLY/GREASE For bottom outlet conversion remove and discard plug. © ITW FINISHING SYSTEMS AND PRODUCTS...
- Page 8 DIRECT DRIVE AGITATOR-REGULATOR HOOK-UP DIRECT DRIVE AGITATOR PETROLEUM JELLY/GREASE For regulator parts see page 13 Refer to SBBI-E-19-095 for information about the Agitator drive unit. Complete drive ref is QMS-430-CE Note Open side of shaft seal (31) faces downwards. FIG 3 Retainer (32) required only for vacuum operation.
- Page 9 GEAR-REDUCED AGITATOR GEAR-REDUCED DRIVE AGITATOR-REGULATOR HOOK-UP Note Use PTFE based thread sealant on all air and fluid connections For regulator parts see page 13 PETROLEUM JELLY/GREASE Note Open side of shaft seal (46) faces downward. Retainer (47) required only for Refer to SBBI-E-19-095 for information about vacuum operation.
- Page 10 PARTS LIST—183S RANGE 9.5 LITRE STAINLESS STEEL TANK ASSEMBLIES 83S-210-CE 83S-211-CE 83S-213-CE ITEM PART NO. DESCRIPTION QN-97 HANDLE ----- ----- QMS-2 PLUG (NON-AGITATED MODELS ONLY) ----- ----- SSG-8184-K2 O-RING (KIT OF 2) QMG-21 AIR MANIFOLD SS-2707 AIR RELIEF VALVE 1/4 NPT-M TIA-4110-CE SAFETY VALVE ASSY, 110 PSI •...
- Page 11 183S & G, 40 AND 60 LITRE TANK ASSEMBLIES Agitator-Regulator Hook-Up Refer to SBBI-E-19-095 for information about with Standard Regulation. the Agitator drive unit, ref QS-5012-CE. For regulator parts see page 13 Complete drive ref is QMS-433-CE (40L) and QMS-434-CE (60L) Note Open side of shaft seal (8) faces downward.
- Page 12 PARTS LIST - 183S - 40 AND 60 LITRE STAINLESS STEEL TANK ASSEMBLIES 183S-1010 183S-1013 183S-1510 183S-1513 ITEM PART NO. DESCRIPTION QMS-46 RETAINING NUT ----- ----- QMG-85 THRUST WASHER ----- ----- ----- THRUST COLLAR ----- ----- • ----- SET SCREW (5/16-18 X 3/8) ----- ----- QMS-447...
- Page 13 PARTS LIST - 183G - 40 LITRE GALVANIZED STEEL TANK ASSEMLBIES 183G-1010 183G-1013 ITEM PART NO. DESCRIPTION QMS-46 RETAINING NUT ----- QMG-85 THRUST WASHER ----- ----- THRUST COLLAR ----- • ----- SET SCREW (5/16-18 X 3/8) ----- QMS-447 THRUST COLLAR KIT (INCL 4 & 5) ----- QMG-409 BEARING ASSY-PLAIN STEEL...
- Page 14 SINGLE REGULATOR AIR CONTROL 85-470 for non-agitated tanks 85-471 for agitated tanks Single Regulator Air Control 85-470 and 85-471 ITEM PART NO. DESCRIPTION 85-470 85-471 § HAR-511 AIR REGULATOR BUSHING-STL-PLTD- 3/8 (m) x • --------- 1/4 (f) VA-542 BALL VALVE 83-1290 GAUGE - 150 PSI SSP-8217-ZN...
- Page 15 BOTTOM OUTLET KIT BOTTOM OUTLET KIT WITH LEGS Allows conversion of tank from standard top outlet to bottom outlet. All bottom outlet wetted parts are stainless steel. 183-3000 for 2-gallon tanks with ¾” bottom outlets Includes three 183-3005 Leg Kits 183-3001 for 10/15-gallon tanks with ¾”...
- Page 16 D-63128 Dietzenbach Germany Glendale Heights, IL 60139 Tel: +49 (0) 6074-403-1 Fax: +49 (0) 6074-403-300 Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only) Email: marketing@itw-finishing.de Toll-Free Fax: 1-888-246-5732 Binks European Sales and Service Listing: www.itwifeuro.com © ITW FINISHING SYSTEMS AND PRODUCTS...