Hamilton Beach Mix 'n Chill Operation Manual page 3

Mixer Safety
To the Operator
Your safety and the safety of others is very important. We have
provided many important safety messages in this manual and
on your appliance. Always read and obey all safety messages.
Read thoroughly and understand the instructions within this
manual before operating or performing any maintenance on
the appliance. Before allowing operation of this appliance, the
operator must be trained and approved by management staff.
The spindle mixer you have purchased is intended for use in
commercial and professional environments requiring trained
operators. Such environments may include, but not be limited
to, restaurants, bars, fast-food outlets, hospitals, catering
businesses, etc.
The spindle mixer is designed to mix drinks made from yogurt,
frozen custard, granita, hard or soft ice cream.
The mixer is also ideal for mixing candy, fruit, and nuts into the
shake. Use of this appliance outside of this scope may result in
fire, electric shock, severe personal injury, or equipment damage.
Unpacking
Carefully remove the mixer from the packaging and take out all
boxes or packets containing attachments or specific items. Check
that all of the parts have been delivered, that the mixer operates
as intended, and that nothing has been damaged in transit.
Contact the mixer supplier to remedy any findings.
Installation
Position the mixer on a sturdy level surface and in an open, well-
lighted environment that provides easy access to all controls, front
and side. We recommend that you position the mixer so that the
working height of the agitator and controls are appropriate for
the intended operator(s).
Noise Level
The equivalent continuous sound level when the mixer is
operating on no-load is less than 70dB(A).
The wheeled bin symbol marked on this mixer signifies compliance with the EU Directive as well as other similar
legislation in effect after August 13, 2005. Therefore, it must be collected separately after its use is completed
and cannot be disposed of as unsorted municipal waste. The user is responsible for returning the product to the
appropriate collection facility, as specified by your local code. For additional information regarding applicable
local laws, please contact the municipal facility and/or local distributor.
Technical Service
For assistance or replacement parts, call our
Technical Service number:
+ + 910-693-4277
8 a.m. – 5:00 p.m. GMT-5 Monday – Friday
www.commercial.hamiltonbeach.com
Model Number
Serial Number
Purchase Date
Dealer Name
Dealer Address
Dealer Phone
– SAVE THESE IN STRUC TIONS –
This Operation Manual must be read and fully understood
before operating or performing any maintenance on your
appliance.
The ON (I)/OFF (O) power switch is provided with an integral
circuit breaker to automatically turn off (O) the unit in over-
current conditions that may occur due to excessive loads to
the motor. When this occurs, allow the mixer to cool down for
30 minutes and then turn the unit ON (I). If the unit does not
operate, contact Technical Service for further direction.
If the supply cord of this appliance is damaged, it must be
replaced by the manufacturer or its service agent or a similar
qualified person.
UK ONLY: If fitted with a non-rewirable U.K. plug, the 13 amp
fuse approved by ASTA to be B.S. 1362 must be used. If you
need a replacement fuse carrier, it must be replaced with the
same colour coded carrier with the same markings. Fuse covers
and carriers can be obtained from approved service agents.
Connection
Observe all electrical governing codes and ordinances.
A 220–240V AC-only, 50–60 Hz, fused electrical supply is
required. (A time-delay fuse is recommended.) It is recommended
that a separate circuit serving only this appliance be provided.
Maintenance
Check the agitator daily for wear or damage. Replace the agitator
every 90 days.
Standard Conformity
The mixer is in compliance with the following European Directives
and related national legislation:
• Machinery Directive 2006/42/EC
• Low Voltage Directive 73/23/EEC
• EMC Directive 2004/108/EEC
Requesting Assistance or Service
Whenever you call to request assistance or service,
you need to know the complete model number of your
equipment. You can find this information on the label on
the back of your spindle mixer.
Please also record the purchase date of your equipment
and your dealer's name, address, and telephone number.
You can also order replacement parts from your local dealer.
Call our customer service number:
+ + 910-693-4277
3