Check the hose from the gas bottle to the unit has no splits - this can be done with soapy water to identify splits in the hose . If odour persist contact Heat Outdoors or a gas supplier . For outdoor use only.
Safety Precautions • Performance and safety service of this heater should be performed annually by a qualified gas engineer. • Do not use the heater in a combustible atmosphere . • Before using the unit check the hose for splits, twists which may cause gas to leak or prevent flow.
Appliance and Location The appliance is for outdoor use only. Do not use indoors or in an enclosed area . Always maintain proper clearance from combustible materials - minimum 800mm from the top of the unit, and a minimum of 650mm from sides .
Installation Important safety requirements: THIS APPLIANCE IS FOR OUTDOOR USE ONLY It is not recommended for this heater to be installed or used indoors, garages or any other enclosed area . DO NOT place articles on or against this appliance . DO NOT use or store flammable materials near this appliance.
Page 8
Parts List Part Number Description Photo Quantity Reflector Emitter screen Protection guard Glass tube Base cylinder Wheels Rubber Ring Parts List...
Assembly Instructions Do not fully tighten fittings until assembly is complete Attach wheels to base cylinder of the Attach 4pcs protection grills to the heater . Line up holes in wheel with holes on top of base cylinder using corresponding holes in base and insert 8pcs M6 nuts (BB) to secure in 2pcs M8x16 screw (FF) through holes.
Page 10
Place the glass tube into the heater . Place the emitter screen assembly onto the protection guards, make sure the thread goes through holes on bottom of emitter screen assembly . Assembly Instructions...
Page 11
Using 8pcs M6 nuts (BB) to tighten protection guards . Parts used: BB M6 8PCS. Secure all bolts . The unit is now fully assembled . Complete Assembly Instructions...
Operation Preparation You will need to purchase a suitable size LPG cylinder that can be installed to the compartment. You must use a pressure regulator and flexible tube which complies with the outlet pressure of the appliance . Connect the hose to the hose connector in the control box .
Lighting Instructions Ignition Instructions Check and ensure that an AA battery is inside the ignition chamber and has power. Ensure the anode (+) faces outwards. Ensure that the control knob is OFF . Slowly open the gas cylinder valve . Press and turn the control knob to LIGHT position, push the igniter to generate spark while keeping control knob in pressed position Check for pilot flame through glass tube.
Cleaning & maintenance To enjoy outstanding performance of your heater for years make sure to perform the following maintenance activities on a regular basis: • Keep exterior surfaces clean . • Use warm soapy water for cleaning. Never use flammable, corrosive or abrasive cleaners .
Storage Between uses: • Turn the control knob to “OFF” position . • Turn LPG cylinder to “OFF” position . • Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, hail, snow). • Cover heater to protect exterior surfaces and to help prevent dust and debris collecting in air passages .
Troubleshooting Problem Solution Pilot will not light • Gas valve may be OFF Turn the gas valve ON • Gas cylinder may be empty. Refill gas cylinder . • Pipes or jets blocked . Clean clean them accordingly and retry . •...
Technical Specifi cations Item Number KLD7003 Flame Heater 0359CR1461 Nominal HEAT (Hs) 10.5 kW (762 g/h) INPUT Appliance I3+(28-30/37) I3B/P(30) Category Gas Reference G30/G31 G30/G31 Normal Gas 28-30/37 mbar 30 mbar Pressure FOR USE OUTDOORS ONLY Close the valve of the gas cylinder or the regulator after use . The use of this appliance in closed areas can be dangerous and is PROHIBITED .
Page 18
Heat Outdoors Unit 9, Stort Valley Industrial Estate Stansted Road, Bishop’s Stortford Hertforshire, United Kingdom CM23 2TU www.heat-outdoors.co.uk 01279 466500 info@heat-outdoors.co.uk...
Need help?
Do you have a question about the 901565 and is the answer not in the manual?
Questions and answers