Setting The Clock (Remote Control Only); Timer And Sleep Operation (Remote Control Only); Timer Playback - Sharp CD-DH899N Operation Manual

Setting the clock (Remote control
only)
CD
USB
In this example, the clock is set for the 12-hour (AM 12:00)
display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button.
Press the or
24-hour display and then press the MEMORY button.
The 12-hour display will appear.
"AM 12:00"
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
"AM 0:00"
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
"0:00"
(0:00 - 23:59)
4
To adjust the hour, press the
then press the MEMORY button. Press the
button once to advance the time by 1 hour. Hold it
down to advance continuously.
5
To adjust the minutes, press the
and then press the MEMORY button. Press the
or button once to advance the time by 1 minute.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
The "CLOCK" will appear or time will be displayed when
the AC power supply is restored after a power failure or
unplugging the unit. If incorrect, readjust the clock as
follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK"
does not appear in step 2, step 3 (for selecting the 12-hour
or 24-hour display) will be skipped.
To change the 12-hour or 24-hour display:
1
Clear all the programmed contents. [Refer to "Factory
reset, clearing all memory" on page 14 for details.]
2
Perform "Setting the clock" from step 1 onwards.
TAPE
button to select 12-hour or
or button and
or
Timer and sleep operation (Remote
control only)
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day.
For example, set the timer as a wake-up call every
morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program,
and use the daily timer to wake up.
Daily timer
Start

Timer playback

Before setting timer:
● Check that the clock is set to the correct time (refer to
page 11). If it is not set, you cannot use the timer
function.
● For timer playback: Plug in USB or load disc/cassette
or dock iPod to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the
select "ONCE SET" or "DAILY SET", and press the
MEMORY button. Set the clock to the correct time if
"ONCE SET" or "DAILY SET" does not appear.
4
Within 10 seconds, press the
select "TIMER SET", and press the MEMORY button.
or
5
To adjust the hour, press the
press the MEMORY button.
button
6
To adjust the minutes, press the
then press the MEMORY button.
7
Set the time to finish as in steps 5 and 6 above.
8
To select the timer playback source (CD, TUNER, USB,
iPod, TAPE or AUDIO IN), press the
Press the MEMORY button.
When you select the tuner, select a station by pressing
the
button. If a station has not been programmed, "NO
PRESET" will be displayed and timer setting will be
canceled.
9
Adjust the volume using the VOLUME control, and then
press the MEMORY button. Do not turn the volume up
too high.
10
Press the ON/STAND-BY button to enter the power
stand-by mode. The "TIMER" indicator lights up and
the unit is ready for timer playback.
E-11
1 minute or more
Stop Start
or
or button, and then press the MEMORY
Once timer
Stop
or button to
or button to
button and then
or button and
or button.