Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nipson Varypress 200
Summary of Contents for Nipson Varypress 200
- Page 1 MAGNETIC PRINTER VARYPRESS 200 Paper guide 22 A6 09NS REV0...
- Page 3 Sept. 2005. Creation. 22 A6 09NS REV0 NIPSON SAS 28, rue E. Thierry-Mieg - BP 257 - 90005 Belfort Cedex - France Tel.: +33 (0)3 84 54 50 00 - Fax: +33 (0)3 84 54 52 18 http:/www.nipson.com - e-mail: info@nipson.com...
- Page 4 A sheet on which to write your remarks is provided at the end of this manual. This document is for information purposes only. NIPSON cannot be held responsible for any damage caused by applying instructions contained within it. Corrections or modifications to the content of this document may be made without notice;...
-
Page 5: Table Of Contents
NIPSON SERVICE ........ - Page 6 Paper guide VARYPRESS 200 Table of contents GENERAL FINISHING / TRANSFORMATION REQUIREMENTS ... . 1 ENVIRONMENT ........... 1 SHEET DIMENSIONAL TOLERANCES.
-
Page 7: Introduction
NIPSON SERVICE NIPSON provides for its customers: Advice on substrate-related subjects not fully covered in this guide; Analysis of substrate types under consideration for customer use, or of those which do not give satisfaction;... -
Page 8: Allowed Formats
Paper guide VARYPRESS 200 ALLOWED FORMATS Ma xi . l e n g th M in i. Mi n i . M ax i. Machine l eng t h wi dth w i dth 6 00 dpi 4 8 0 dpi... -
Page 9: Paper Characteristics
Give paper with a greyish color which tends to restrict their use. Kraft pulps Give brown-colored paper or cardboard having high mechanical strength. NOTA : NIPSON recommends using a 100% chemical-pulp paper. Paper using mechanical or recycled pulp may, however, give good results for certain applications. 2.1.2. -
Page 10: Physical Characteristics
Paper guide VARYPRESS 200 PHYSICAL CHARACTERISTICS These characteristics affect directly the print quality and paper passage in the printer. Paper weight Is a basic characteristic which has an influence on mechanical behavior. It is given in terms of either the mass per square meter of paper (g/m ), or the weight in pounds of 500 sheets of paper cut to 17"... -
Page 11: Paper Specifications
Paper guide VARYPRESS 200 PAPER SPECIFICATIONS Paper weight: from 64 g/m to 160 g/m Moisture Content: From 2.5% to 7%. Relative Humidity: From 15% to 60%. (stabilized at 23ºC) Surface resistivity: From 1010 to 1013 ohms. Volume resistivity: From 5 x 1010 to 1014 ohms par cm. -
Page 12: Self-Adhesive Labels
Paper guide VARYPRESS 200 Self-adhesive labels CHARACTERISTICS / SPECIFICATIONS 3.1.1. Backing sheet material Paper type: Kraft paper is recommended for its high opacity and mechanical strength. Paper weight: From 85 to 95 g/m Dynamic rigidity: More than 0.3 mN x m (machine direction). -
Page 13: Front Face Characteristics
Paper guide VARYPRESS 200 3.1.3. Front face characteristics Recommended paper weight:80g/m Bekk smoothness:More than 20 seconds. Opacity:More than 85%. Moisture content:From 3 to 6,5%. Surface resistivity:From 1010 to 1013 ohms at 100V. Stiffness:From 0.10 to 0.20 mN x m Label separation:No separation of label from backing is allowed under the following conditions: a) temperature 30ºC, bending radius 25mm, bending angle 135º, time duration 30s;... -
Page 14: Special Substrate Types
Paper guide VARYPRESS 200 Special substrate types The flash fusing system used allows printing on a wide variety of printing substrates, particularly plastics or other fragile materials which would be deformed by the heating effect of a radiant oven or of hot rollers. -
Page 15: Preglued Substrate
Paper guide VARYPRESS 200 Effect on substrate surface Preprinting / drying shall not cause irregularities (waviness) in the substrate which prevent uniform contact between substrate and image drum during the transfer of toner. Electrical Conductivity The use of preprinting toners must not result in electrical surface or volume conductivity outside the range of values specified for paper in section 2.3 “Paper Specifications”. -
Page 16: Laminates
Paper guide VARYPRESS 200 card (curved concave down) support medium ≤ 0.4N Cards which curve away from the support medium (concave up) are not acceptable. LAMINATES Laminated substrates up to 160g/m can easily be run on the printer. These include: plastic-coated paper cards mounted on a paper support, and substrates with "embedded"... -
Page 17: Carbonless Self-Copy Paper
(during preprinting) to areas to be printed. Tests should be performed in consultation with the carbonless supplier and NIPSON in order to verify the level of image quality obtainable. -
Page 18: General Finishing / Transformation Requirements
Paper guide VARYPRESS 200 General finishing / transformation requirements ENVIRONMENT In order to maintain dimensional stability, forms must be finished in a controlled environment with the following conditions: temperature between 20ºC and 23ºC; relative humidity between 40% and 50%. Return to table of contents... -
Page 19: Sheet Dimensional Tolerances
Paper guide VARYPRESS 200 SHEET DIMENSIONAL TOLERANCES 6 ± 0.7 0.15 max. 90° 12.7 ± 0.05 distance: nominal ± 0.5 width: nominal ± 0.5 4 ± 0,1 0.1 max. 0.1 max. fold perforation Cumulative tolerance between any two holes on the same side which are distant by 254mm is ± 0,3 mm (±... -
Page 20: Perforations
Paper guide VARYPRESS 200 PERFORATIONS 5.3.1. Sheet edges at fold perforations To avoid tearing, there must be a tie of width ≥ 1 mm beginning at a distance of ≤ 1 mm from sheet edge. 5.3.2. Fold perforation tensile strength For fanfold forms, fold perforation tensile strength must be between 800 and 2000 N/m. -
Page 21: Other Perforations
Paper guide VARYPRESS 200 5.3.5. Other perforations Paper must be continuously present at one or more of the following positions (End of Paper optical sensor positions): Standard printer - 50mm, 152,5mm, 232mm S.E.D. printer - (recto) - 50mm, 152,5mm, 232mm... -
Page 22: Packaging And Storage
Paper guide VARYPRESS 200 Packaging and storage PACKAGING REQUIREMENTS The packaging must protect the paper during storage at the supplier and at the user site as well as during transport. Fanfold forms Cartons must be of the telescoping type without metallic staples, and close-fitted to avoid any paper movement inside the carton. -
Page 23: Storage Requirements
Paper guide VARYPRESS 200 STORAGE REQUIREMENTS Stored paper must be left in its original packaging, off the floor and away from open windows or heat sources. It must be stored under conditions as close as possible to its optimum utilization conditions, using the following guidelines: Les conditions climatiques doivent être si possible proches des conditions d'utilisation :... - Page 24 ADRESSE / ADDRESS: Remettez cet imprimé à un responsable de NIPSON ou renvoyez le à l’adresse ci-dessous. Please give this technical publications remarks form to your NIPSON representative or mail to address below. NIPSON SAS 28, rue E. Thierry-Mieg - BP 257 - 90005 Belfort Cedex - France Tel.: +33 (0)3 84 54 50 00 - Fax: +33 (0)3 84 54 52 18...