Televic Confidea G3 Installation & User Manual
  1. Manuals
  2. Brands
  3. Televic Manuals
  4. Wireless Access Point
  5. Confidea G3
  6. Installation & user manual

Televic Confidea G3 Installation & User Manual

Hide thumbs Also See for Confidea G3:
Table of Contents

Advertisement

Quick Links

See also: Installer and User Manual
Confidea G3
Installation – User guide

Advertisement

Table of Contents
loading

Related Manuals for Televic Confidea G3

Summary of Contents for Televic Confidea G3

  • Page 1 Confidea G3 Installation – User guide...
  • Page 2 All terms mentioned in this manual that are known to be trademarks or service marks have been appropriately capitalized. Televic NV cannot attest to the accuracy of this information. Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark.

  • Page 3: Table Of Contents

    1.3.1. Compatibility ........................... 6 1.3.2. Mount the Confidea Wireless access point (WCAP) ..............7 1.3.3. Access the Confidea G3 web server ..................9 Introduction to the web server ....................14 2.1. Compatibility ..........................14 2.2. Quick start to the application ....................14 Configure network settings ....................
  • Page 4 Linking CoCon to the WCAP ....................33 7.1. Introduction ..........................33 7.2. Upload license .......................... 33 Confidea wireless and Plixus ....................34 Camera control ........................35 9.1.1. Introduction ........................... 35 9.1.2. Configure camera control ...................... 35 USER GUIDE – Confidea G3...

  • Page 5: Introduction

    This indicates that something is very important. Important information is something that you need to do in order to accomplish a certain task. This provides safety precaution information, that is, information that you need to be careful about to prevent potential problems when using our systems. USER GUIDE – Confidea G3...

  • Page 6: About Confidea G3

    Link the Confidea system to a camera (F) using the LAN connection (D). You can find more information on how to configure this in the chapter Camera control. Figure 1 Confidea G3 setup 1.3. Getting started 1.3.1. Compatibility This user manual applies to the following products:...

  • Page 7: Mount The Confidea Wireless Access Point (Wcap)

    It is important not to point the antennas directly towards the units. • The angle of the antennas in relation to the position of the delegate units affects the overall RF link quality between WCAP and delegate units. See the images below for more information. USER GUIDE – Confidea G3...
  • Page 8 WCAP by positioning the antennas in relation to the position of the delegate units. Note : Certain construction materials such as concrete or metal may absorb part of the RF signal radiation, resulting in a reduction of the maximum distance between the access point and the units. USER GUIDE – Confidea G3...

  • Page 9: Access The Confidea G3 Web Server

    1. Plug in the 24V adapter to the device and the power socket. 2. Connect the LAN cable to your computer or the LAN network that contains your computer. 3. Switch on the Confidea G3. The left LED light will start blinking white, this means the system is booting.
  • Page 10 3. Click Change adapter settings in the menu on the left. 4. Right-click the Local Area Connection and select Properties. 5. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. USER GUIDE – Confidea G3...
  • Page 11 2. Press Enter. 3. Follow the wizard for initial setup of the WCAP. 4. In the second step select your language and the region. The region will determine which frequencies are available. USER GUIDE – Confidea G3...
  • Page 12 6. In step four you can define a user name and password to login to the web server. If you do not enable this, you can leave these fields blank on the login screen. USER GUIDE – Confidea G3...
  • Page 13 2. When you release the button a screen will appear to indicate that the device will reset. After this action the IP address will be reset to its default value. USER GUIDE – Confidea G3...

  • Page 14: Introduction To The Web Server

    Figure 2: the web server’s home page. You can click one of the settings name (2) to go to its configuration page. When you click the Menu icon, you will see all available features that you can configure. USER GUIDE – Confidea G3...
  • Page 15 Change user name and password. Login settings Device and system information. You can upload your System info CoCon license here. Contains all the systems logging. Logging Configure the encryption settings. Encryption Update the WCAP and delegate units. Update version USER GUIDE – Confidea G3...

  • Page 16: Configure Network Settings

    Enter the fixed IP address of the WCAP. (Only available in static mode). Subnet mask Define the subnet of the WCAP Gateway Is the access point to another network. API TCP port 2. Click Save settings. USER GUIDE – Confidea G3...

  • Page 17: Frequency Settings

    Confidea WCAP would use the same frequencies. When the Confidea wireless system is set to manually select the wireless carrier frequency, then you must check that the Confidea wireless carrier does not overlap the already occupied Wi-Fi wireless carrier channels. USER GUIDE – Confidea G3...

  • Page 18: How To Avoid Interference

    Note : The Wi-Fi access points must have sufficient capacity to ensure Wi-Fi connection for all Wi-Fi devices present. If Wi-Fi connection capacity is insufficient for all mobile Wi-Fi devices present, then unstable functionality of the Confidea wireless system due to interference cannot be excluded! USER GUIDE – Confidea G3...

  • Page 19: Configure Conference Settings

    Microphone LEDs blinking red at a rate of 2 Hz is an indication that the units are trying to connect to the WCAP. Microphone LEDs blinking red at a rate of 1 Hz is an indication that the units are waiting for the initialization. USER GUIDE – Confidea G3...

  • Page 20: Edit Units

    Once units are linked to the WCAP it is possible to edit some of the features of the units. You can change the name, create groups and add units to specific groups. 1. Click Edit configuration. 2. Click the edit icon to change the name and press ENTER when ready. USER GUIDE – Confidea G3...

  • Page 21: Configure Discussion Options

    Chairman units always have priority. When the maximum is reached , the microphone of the delegate unit which was switched on first , will be automatically deactivated. A maximum six microphones can be active at the same time USER GUIDE – Confidea G3...
  • Page 22 A high microphone preset combined with strong audio input may result in the perception that the VOX activation is too slow due to the limiter release time. USER GUIDE – Confidea G3...

  • Page 23: Configure Audio Options

    It is possible to configure different audio such as the sensitivity of the microphone. Select Audio from the menu to see these settings. The settings are grouped into three categories: General, AUX IN (1) and AUX OUT(1). USER GUIDE – Confidea G3...

  • Page 24: General Audio Settings

    External compressor limiter device : in this case Microphone preset must be set to • Close, to allow maximum adjustability on the external compressor-limiter device (see also AUX control settings). USER GUIDE – Confidea G3...
  • Page 25 External processing: this option allows you to add an external signal processing equipment or a mixing board. ≤6 ∑ Level: 0..32 Status ∑ detector Std. ON Std. 32 External processing unit Level: 0..32 Status Signal present Std. ON Std. 32 USER GUIDE – Confidea G3...

  • Page 26: Aux In Settings

    5.3.2. AUX IN settings The Confidea G3 WCAP has one auxiliary input. You can configure the following AUX IN settings: Parameter Description AUX IN status Switch the input on or off AUX IN level Adjust the volume of the input...
  • Page 27 E. Click to switch off an individual microphone. F. Click the icon to send the unit into request mode (green blinking microphone LED). Units in request are indicated by a green request icon G. Color indicates to which group the delegate belongs. USER GUIDE – Confidea G3...

  • Page 28: System Configuration

    2. On this page you can see the firmware version of the WCAP (A) as well as the firmware version of the delegate units (B) 3. To check whether you have the latest version, go to https://www.televic- conference.com/en/confidea-g3-software-updates and select Confidea G3. On these pages you can also see the latest release notes. USER GUIDE – Confidea G3...

  • Page 29: Update Firmware Of Wcap And Wdu

    The web server will show you the progress of the installation. If the update fails, the system will boot in golden mode allowing you to retry the update. During WDU update the microphone LEDs on the units will alternate between red and green. USER GUIDE – Confidea G3...

  • Page 30: Login Settings

    Shows device specific information of the WCAP System information Shows system information such as IP address and mode License Place to upload your CoCon license, click Upload license Reboot WCAP Click Reboot WCAP to restart the device USER GUIDE – Confidea G3...

  • Page 31: Logging

    , warning and other messages. You can easily filter which messages you want to see by clicking the message button on top of the page (A). The following information is available: Information type Description Messages concerning delegate units connecting, Info microphone activations Messages concerning change of settings Setting USER GUIDE – Confidea G3...

  • Page 32: Encryption

    If another encryption option is selected, then only those units having the correct encryption will be able to log onto the system. If you want to add another unit to the system, you need to select the default encryption first. USER GUIDE – Confidea G3...

  • Page 33: Linking Cocon To The Wcap

    P-number (can be found on the CoCon package) to CoCon- license@televic.com. You will receive an email containing the requested license file. 7.2. Upload license The license is an XML file, you can open the file to check whether the license contains the correct modules.

  • Page 34: Confidea Wireless And Plixus

    Plixus engine. When you want to update the Confidea WCAP and the WDUs you will have to uncouple Confidea from the Plixus network. USER GUIDE – Confidea G3...

  • Page 35: Camera Control

    Micnr : is the microphone number , can be one or more digits. Status : 0 = off, 1 = on, 2 = request , 3 = prior For example: data sent when microphone 7 is in request : {“UID”: 7,“status”: 2} USER GUIDE – Confidea G3...

Table of Contents