Subscribe to Our Youtube Channel
Related Manuals for Country Clipper Professional Bagging System
Summary of Contents for Country Clipper Professional Bagging System
- Page 1 PROFESSIONAL BAGGING SYSTEM MODEL# PBS DESIGNED FOR THE BOSS AND CHARGER SERIES OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL#: Q0418 PART# 629FS-001A...
-
Page 2: Table Of Contents
PROFESSIONAL BAGGING SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
H. REMEDIED EXCLUSIVE. The only remedies the purchaser has in connection with the breach or performance of any warranty on Country Clipper bagging systems are set forth above. In no event will Country Clipper be liable for special incidental or consequential damages. -
Page 5: Introduction And Description
SECTION I INTRODUCTION AND DESCRIPTION For 25HP Kawasaki or 23,27,28,& 30HP Kohler, replace 1-1 Introduction these parts with the engine pulley assembly number 6 Your grass collection system has been designed to give P#(A0611), 7/16” lock washer P#(K0140), and 7/16”-20 x you a low maintenance, simple, and effective way to 3-3/4”... -
Page 6: Right Mount Plate Assembly Installation
Figure 2-4 (4) 3/8”-16 x 1-1/2” HHCS 2-2 Right PTO Mount Plate Assembly (4) 3/8”-16 Nyloc Nut Installation Fasten the right PTO mount plate assembly P#(A1230) to the right panel guard using (2) 1/2”-13 x 1-1/2” HHCS P#(K1233) and (2) 1/2”-13 nyloc nut P#(K1247). Use existing hardware from the rear panel guard where indicated. -
Page 7: Universal Pto Installation
2-6 Universal PTO Installation 2-8 Belt Installation Remove the belt guard. Loosen the (4) bolts P#(K1191), To mount the PTO assembly, insert the pivot rod on the (2) on each side, that secure the gear box assembly to PTO assembly P#(A0623) into the mounting slots the PTO assembly P#(A0623) (Figure 2-8a and 2-8b). -
Page 8: Cam Assembly Adjustment
2-11 Top Assembly To Upper Frame 2-9 Cam Assembly Adjustment The cam assembly P#(A0422), which controls the Assembly Installation blower belt tension, comes from the factory pre-adjusted. Align the pivot brackets of the top assembly P#(A0585) If the belt is too tight or becomes too loose, remove the to the pivot point on either side of the upper frame hair pin clip P#(K0130) from the belt tension rod assembly. -
Page 9: Blower Cone Installation
2-13 Blower Cone Installation 2-14 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially To Remove: First remove the 3/8”-16 x 1-1/2” HHCS thread the bolts into each of the two tabs located on the P#(K1211) (#1) , taper lock bushing washer P#(K0278) -
Page 10: Length Of Hose Adjustment
2-15 Length Of Hose Adjustment Hose Clamp Figure 2-18 The hoses in steps 2-16 and 2-17 must be cut to fit your machine. Follow steps 2-16 and 2-17. do not cut the hoses until you have tried to fit them on your machine. Remember that the hoses have to be long enough to adjust for the blower assembly’s movement as well as allow for enough clamping surface between the inlet,... -
Page 11: Exploded Part Views And Assemblies
Exploded View Of The A0551 - Bagger Assembly (2) K1144 - 5/16”-18 x 1” CARRIAGE BOLT (6) K1142 - 5/16”-18 x 3/4” CARRIAGE BOLT (4) K1010 - 1/4”-20 x 5/8” CARRIAGE BOLT (1) V0002 - PLASTIC TOP (2) K1126 - 1/4”-20 (1 LEFT, 1 RIGHT) FLANGE NUT B0237 - PIVOT... - Page 12 MODEL#: 49031302 PROFESSIONAL MOWER NAME: COUNTRY CLIPPER BAGGING MOWER MODEL: BOSS & CHARGER SYSTEM MOWER DECK SIZE: 52” & 60” VAC NAME: 13 CUBIC FOOT PRO BAGGER FOR YEAR: 2011 PTO DRIVEN REVISED: 5/17/2011 SHIVVERS PART#: 629FS-001A A1136 UNIT ASSEMBLY 8”...
- Page 13 Exploded Parts View PTO Assembly A0623...
- Page 14 PTO Parts List Item Document Title Quantity Number Number A0429 GEAR BOX ASSEMBLY K0348 3/8"-16 x 2" ALL THREAD HHCS K0047 3/8" FLAT WASHER 1.00 OD x .446 ID x .075 T K0353 1/4"-20 x 1/2" HHSTS K1159 5/16"-18 x 2" ALL THREAD HHCS K1178 5/16"-18 FLANGE NUT A0144...
-
Page 15: Installation/Removal Of Collection Bags
2-20 Installation/Removal Of Figure 2-20b Plastic Top Collection Bags To install the bag onto the bag ring, first make sure the bag ring end caps are fastened to the bag ring. Place the seam openings of the bag onto the bag ring openings and turn the bag until the slot bracket in the bag ring is protruding from the opening in the bag (Figure 2-20a). -
Page 16: Operating Instructions
SECTION III 3-3 Disengagement Of The Blower OPERATING INSTRUCTIONS A. To disengage the blower, rotate the engagement 3-1 General Safety handle towards the mower. Only qualified people familiar with this operator’s manual WARNING: The blower will continue to spin. DO NOT and the mower’s operator’s manual should operate this TOUCH the blower, pulleys, or the belt until the tractor is machine. -
Page 17: Lubrication
Country Clipper and include by the manufacturers to be affixed to the component. the following information on the chart below. -
Page 18: Safety Decals
SAFETY DECALS To promote safe operation, Country Clipper supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #:R1083 Enage/Disengage Label Part #: R1052... - Page 20 Country Clipper Division of Shivvers Mfg. Inc 613 W. English | Corydon, IA | 50060 Phone: 1-800-344-8237 | 641-872-2544 Fax: 641-872-1593 E-Mail: countryclipper@countryclipper.com...
Need help?
Do you have a question about the Professional Bagging System and is the answer not in the manual?
Questions and answers