Epson SureColor F6000 Series Settings Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. SureColor F6000
  6. Settings manual
Epson SureColor F6000 Series Settings Manual

Epson SureColor F6000 Series Settings Manual

Hide thumbs Also See for SureColor F6000 Series:
Table of Contents

Advertisement

Quick Links

SureColor F6000/B6000 series
Setting Guide (install)
Seiko Epson Corp.
COMMERCIAL PRINTER CS QUALITY ASSURANCE Dept.
SEGroup Confidential Until: Permanent

Advertisement

Table of Contents
loading

Related Manuals for Epson SureColor F6000 Series

Summary of Contents for Epson SureColor F6000 Series

  • Page 1 SureColor F6000/B6000 series Setting Guide (install) Seiko Epson Corp. COMMERCIAL PRINTER CS QUALITY ASSURANCE Dept. SEGroup Confidential Until: Permanent...
  • Page 2 Revision Status Revision Date of Issue Description March 8, 2013 First release August 27, 2014 Revised Clear the package material Correct mistakes SEGroup Confidential Until: Permanent...
  • Page 3 < Caution > Always wear gloves for assembly to avoid injury from sharp metal edges. When handling the ink packs Wear protective eyewear, gloves, and mask when performing maintenance. SEGroup Confidential Until: Permanent...

  • Page 4: Table Of Contents

    Content 1-1 Packaging (Main Unit) 3-5 Fixing the Ink Tank 1-2 Packaging (Ink Support Assy.) 3-6 Setting the Ink Supply cover 1-3 Packaging (Ink Supply cover) 4-1 Fill ink into ink tank 2-1 Assembly (Stand) 5-1 FW update 2-2 Assembly (Main unit + Stand) 6-1 Ink charge 3-1 Setting the Ink Support Assy.

  • Page 5: Packaging (Main Unit)

    1-1 Packaging (Main Unit) 1. Printer 2. Adapter 3. Document pack 4. AC cable 5. Stand 6. Hex wrench 7. Hex bolt （Fix the printer and stand) SEGroup Confidential Until: Permanent...

  • Page 6: Packaging (Ink Support Assy.)

    1-2 Packaging (Ink Support Assy.) 8. Spacer (18pcs) 12. Screw ( for Ink Support Assy. 4×8(10 pcs) 9. Plate B 10. Screw (for Ink tank) 13. Ink Support Assy. S taite3×8 (4pcs) 11. Screw (for ink tank height) 3×18 (2 pcs) SEGroup Confidential Until: Permanent...

  • Page 7: Packaging (Ink Supply Cover)

    1-3 Packaging (Ink Supply cover) 14. Plate A 15. Plate C 16. Hex bolt (Short) (for Plate A and Plate C) 17. Hex bolt (Long) (For Ink Supply cover ) 18.Screw (Ink supply ink and Plate 3×8（2pcs） 19. Ink Supply Cover SEGroup Confidential Until: Permanent...

  • Page 8: Assembly (Stand)

    2-1 Assembly (Stand) It is recommended to assemble the stand by a group of three. Plate A Plate C Give the screws shown in the figure a couple of turns to fasten the parts temporarily. The items in the following steps can not be attached if the screws are too tight.
  • Page 9 2-1 Assembly (Stand) Set Plate A to the Stand Right You must set this plate before placing main unit on the stand. Set hex bolts temporarily. Before using the printer, be sure the stand is fixed in place. When moving the printer, unlock the casters.

  • Page 10: Assembly (Main Unit + Stand)

    2-2 Assembly (Main unit + Stand) When carrying the printer, use at least 4 persons. When lifting the printer unit, only hold the highlighted area. Otherwise, it may affect normal operation and printing. SEGroup Confidential Until: Permanent...
  • Page 11 2-2 Assembly (Main unit + Stand) SEGroup Confidential Until: Permanent...

  • Page 12: Setting The Ink Support Assy

    3-1 Setting the Ink Support Assy. Main unit bottom 1. Set Ink support assy. (Black: 10 screws) back side Main unit bottom front side Set Plate B （2 screws) temporarily SEGroup Confidential Until: Permanent...

  • Page 13: Setting The Ink Tank

    3-2 Setting the Ink Tank Push topside and Insert the INKHOLDER Put the CSIC Chips on the Slider Caution: Set the Bk Ink Tank at first. (Most right side) See next Set Ink Tank with reference to Ink Supply Cover page SEGroup Confidential Until: Permanent...
  • Page 14 3-2 Setting the Ink Tank Cut position of Ink Tank Set to fit between cut position of Ink Tank and hook of Ink Holder Hook of Ink Holder SEGroup Confidential Until: Permanent...
  • Page 15 3-2 Setting the Ink Tank Check the depth of Hook Good SEGroup Confidential Until: Permanent...

  • Page 16: Confirming The Ink Tank Position

    3-3 Confirming the Ink Tank position Check the vertical position of Ink Tank It is not enough to hold/insert It is enough to hold/insert the ink the ink tank. tank. Good If it is not enough to hold/insert the ink tank, please set this ink tank again.

  • Page 17: Adjusting The Ink Tank Height

    3-4 Adjusting the Ink Tank height Check the front and rear position of Ink Tank Good This Tank is not insert enough. SEGroup Confidential Until: Permanent...
  • Page 18 3-4 Adjusting the Ink Tank height Set the white adjusting plastics one by one. 1. Right side 2. Left side Adjusting plastics 3. Right side 4. Left side for ink tank height. (included 18pcs) SEGroup Confidential Until: Permanent...
  • Page 19 3-4 Adjusting the Ink Tank height 5. Right side 6. Left side 7. Right side Once you do feel the staggering (even if you find there is No Gap please set one more plastic parts again. <One time only!> feel the staggering Don’t push ink tanks up during inserting adjusting...

  • Page 20: Fixing The Ink Tank

    3-5 Fixing the Ink Tank Holding down the Ink Tank and tighten 4pcs screws to hold ink tank itself. SEGroup Confidential Until: Permanent...
  • Page 21 3-5 Fixing the Ink Tank Tighten 2pcs screws (Home and Full sides). Home side Full side SEGroup Confidential Until: Permanent...

  • Page 22: Setting The Ink Supply Cover

    3-6 Setting the Ink Supply cover Put the Ink Supply cover on the Hex bolt temporarily Tighten Hex bolt Tighten Hex bolt Tighten 2 screws SEGroup Confidential Until: Permanent...

  • Page 23: Fill Ink Into Ink Tank

    4-1 Fill ink into ink tank 1. Shake all ink packs before ink filling ink tank. （Horizontal :5cm (both side) 15times/5sec. 2. Cut the pour spot of ink pack by scissors. Don’t cut deeply. Because this position is guide when pure the ink.
  • Page 24 4-1 Fill ink into ink tank 3. Fill the ink tank with the ink from the ink pack. <Caution> Get all the ink out of the ink pack so that there is none remaining. Do not use the ink in an ink pack to refill multiple different ink  tanks. This can cause messages from the remaining ink warning  system to not be displayed properly. Do not turn on printer before filling all inks. Confirm whether Ink Tank color is suitable for Ink Pack color when  fill the ink.  SEGroup Confidential Until: Permanent...

  • Page 25: Fw Update

    5-1 FW update Please do NOT turn on printer before filling all inks! After filling all ink as pictures, please turn on printer by FW update mode. SEGroup Confidential Until: Permanent...
  • Page 26 5-1 FW update 1) Please check the CURRENT FW version. 2) Please update the latest FW. (Printer turn off automatically.) 3) Please turn on the printer by FW update mode again. 4) Please check the FW version which you updated. If OK, please turn off printer. SEGroup Confidential Until: Permanent...

  • Page 27: Ink Charge

    6-1 Ink charge 1. Power ON (Normal mode) 2. Set the printer setting (Language, Calendar etc.) 3. Starting Ink Charge While Ink charging, don’t touch the printer. Because some bad influence for ink charge process. SEGroup Confidential Until: Permanent...
  • Page 28 Reference :When you can not proceed ink charge, check the ILS sensor. 1. Turn ON “Service man mode” [Menu]+[ ]+[OK] 2. [SELF TESTING] [Mecha Adjustment] [Sensor Check] ILS C ILS is “ON “ C Ink Tank position is All Color ILS “OFF” Check again of C Ink Tank position FYI: Normal Power ON mode error...

  • Page 29: Replace The Maintenance Box

    7-1 Replace the Maintenance box Replace the maintenance box of right side After Ink charge, “Replace and left side. maintenance box soon” message appear on the panel. (Left side maintenance box is not consume while printing and will not reach end till (Right side maintenance box product life.) is near full)

  • Page 30: Nozzle Check

    8-1 Nozzle check Check the nozzle check pattern. If you find the nozzle missing, please do cleaning (CL1 or CL2 or CL3). SEGroup Confidential Until: Permanent...

  • Page 31: Request For Customer

    9-1 Request for customer • Please inform the user of the next page certainly! • Please present the next page to user and encourage the points of caution. SEGroup Confidential Until: Permanent...
  • Page 32 9-1 Request for customer First ink refill after initial setup Replace chip unit and refill ink when ink level from bottom of the tank becomes about70mm. Second ink refill and after インク残量を確認して ① ② ください。 Ink level is more than 70mm: Replace chip unit with new Recommends to continue using the printer until When this message appears,...
  • Page 33 SEGroup Confidential Until: Permanent...

This manual is also suitable for:

Surecolor b6000 series

Table of Contents