Download Print this page

Makita DUT130 Instruction Manual

Hide thumbs


Cordless Mixer
Read before use.



  Related Manuals for Makita DUT130

  Summary of Contents for Makita DUT130

  • Page 1 INSTRUCTION MANUAL Cordless Mixer DUT130 DUT131 Read before use.
  • Page 2: Specifications

    Symbols Noise The followings show the symbols used for the equip- The typical A-weighted noise level determined accord- ment. Be sure that you understand their meaning before ing to EN60745-2-1: use. Model DUT130 Sound pressure level (L ) : 74 dB(A) Read instruction manual. Uncertainty (K) : 3 dB(A) Model DUT131 Sound pressure level (L ) : 74 dB(A) Do not use the tool in the rain.
  • Page 3: Ec Declaration Of Conformity

    The vibration total value (tri-axial vector sum) deter- adapter plugs with earthed (grounded) power mined according to EN60745-2-1: tools. Unmodified plugs and matching outlets will Model DUT130 reduce risk of electric shock. Work mode: operation without load Avoid body contact with earthed or grounded Vibration emission (a ) : 2.5 m/s...
  • Page 4 Do not let familiarity gained from frequent use Keep handles and grasping surfaces dry, of tools allow you to become complacent and clean and free from oil and grease. Slippery ignore tool safety principles. A careless action can handles and grasping surfaces do not allow for cause severe injury within a fraction of a second.
  • Page 5 SAVE THESE INSTRUCTIONS. surface. SAVE THESE INSTRUCTIONS. CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that WARNING: DO NOT let comfort or familiarity have been altered, may result in the battery bursting with product (gained from repeated use) replace causing fires, personal injury and damage. It will...
  • Page 6: Functional Description

    To install the battery cartridge, align the tongue on the FUNCTIONAL battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place DESCRIPTION with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely. After installing the battery cartridge, close the battery CAUTION: Always be sure that the tool is cover securely. switched off and the battery cartridge is removed before adjusting or checking function on the tool. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, Installing or removing battery it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Page 7 Tool / battery protection system The tool is equipped with a tool/battery protection sys- tem. This system automatically cuts off power to the motor to extend tool and battery life. The tool will auto- matically stop during operation if the tool or battery is placed under one of the following conditions: Overload protection When the tool or battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this sit- uation, turn the tool off and stop the application that ► 1. Switch trigger 2. Lock button 3. Trigger-lock button caused the tool to become overloaded.
  • Page 8: Electronic Function

    Installing the shaft function Optional accessory If you install the battery cartridge while pulling the For DUT130 switch trigger or locking the switch trigger, the tool does Tighten the shaft into the shaft holder. not start. To start the tool, release the switch trigger, and then pull the switch trigger.
  • Page 9 Tighten the chuck by hand, and then place the Hook chuck key in each of three holes and tighten it clock- wise. Be sure to tighten the chuck key at all three holes Optional accessory evenly. CAUTION: Always remove the battery when hanging the tool with the hook. CAUTION: Never hook the tool at high loca- tion or on potentially unstable surface. ► 1 . Chuck key 2. Chuck To remove the shaft, turn the chuck key counterclock- wise at one of the holes, and then loosen the chuck by hand. ► 1 .
  • Page 10: Operation

    Tighten the shaft holder with a wrench while hold- OPTIONAL ing the spindle with another wrench. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center.
  • Page 12 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885670A220 20180910...

This manual is also suitable for: