Switch Installation - MINN KOTA DeckHand DH 25R Owner's Manual

Item Part Description
1 2370209 Cover DH-25R
2 2303005 Pig Ring
3 2372121 Screw-#8-18x 1-1/2 Stallgrd (2 .ea)
4 2372111 Screw-#8-18x3/4 Stallgrd (2 .ea)
n 2377803 Motor Assembly - DeckHand- Includes 6-13
6 2375400 Shrink Tube 1/4x1-3/4 (2 .ea)
8 350-154 Gear
9 990-077 Washer - Nylatron (3 .ea)
10 990-075 Washer - Steel (3 .ea)
11 410-015 Cover- Housing
11a 337-015 Gasket
12 830-036 Screw - 10-32x.375 (4.ea)
13 788-030 Retaining Ring
14 2223455 Screw-#10-32x1/2 (3 .ea)
14a 2261718 Washer- Lock Star #10 Ext Tooth 3.ea)
15 2377900 Spool includes 60' rope
16 2370000 Bearing-Spool
17 2263010 E-Ring 3/8 Dia Shaft
18 2371900 Base- Mounting E-Coat
19 2374010 Switch-Momentary Anchor
20 2372130 Screw-#4-40x3/4 PPH (2 .ea)
21 2373100 Nut-Con/Mom Swt Anchor (2 .ea)
22 2372700 Spring-Anchor
23 2372900 Grommet-Anchor Cover Short (2 .ea)
24 2372910 Grommet-Anchor Cover Long (2 .ea)
25 2376300 Wire- Routing Clip (2 .ea)
2994803 Bag Assembly (includes 26-30)
n
26 2153501 Bolt- Mounting 3500 w/stallgd (4 .ea)
27 2301720 Mounting Washer-Rubber (6 .ea)
29 2151726 Washer 5/16 STD SS (4 .ea)
30 2153100 Nut 5/16 (4 .ea)
34 2372100 Screw, #8
39 2374000 Switch-Control Anchor
40 2376500 Switch Housing (DH- 25R)
41 2376510 Switch Plate
42 2372150 Screw-Switch Plate 6-20x1/2 (3 .ea)
43 2370700 Control Wire (DH-25R)
44 2370602 Leadwire (DH- 25R)
45 2371610 Rope Guide
46 2372710 Spring-Rope Guide
47 2151700 Washer- Eye Shaft (2 .ea)
48 2372615 Cotter Pin 3/32x3/4 (2 .ea)
49 2378204 Circuit Breaker
50 2372031 Tubing- Heat Shrink
52 2371412 Connecting Cable 14ga
53 2998411 Davit Assembly
54 2992312 Large Roller Assembly
55 2992306 Small Roller Assembly
56 2991503 Sleeve Roller Assembly
57 2370820 Safety Chain Assembly
57a 2370806 Anchor Shackle
58 2992620 Safety Pin Assembly
59 2774805 Mounting Bolts and Nuts (4 each)

SWITCH INSTALLATION

Your DeckHand control switch assembly (39) is equipped with an eighteen foot control wire,
allowing convenient mounting almost anywhere in the boat.
1. Select a control switch mounting location. If wire routing or control switch mounting requires
disconnecting of wires within switch housing (40), take special care to insure that proper
reassembly is achieved- refer to wire diagram on page 11.
2. Securely attach switch housing assembly with the two screws (34) provided.
U
O
P
D
F
O
F
W
N
Switch -center in "OFF" position before battery hook-up.
Switch housing