Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Quick Manual
Digidesign
96i I/O Guide
2001 Junipero Serra Boulevard
Daly City, CA 94014-3886 USA
Digidesign
tel: 650·731·6300
fax: 650·731·6399
Technical Support (USA)
tel: 650·731·6100
fax: 650·731·6384
Product Information (USA)
tel: 650·731·6102
tel: 800·333·2137
International Offices
Visit the Digidesign Web site
for contact information
Web Site
www.digidesign.com
Advertisement
Table of Contents
Related Manuals for DigiDesign 96i I/O
Summary of Contents for DigiDesign 96i I/O
- Page 1 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650·731·6300 fax: 650·731·6399 Technical Support (USA) tel: 650·731·6100 fax: 650·731·6384 Product Information (USA) tel: 650·731·6102 tel: 800·333·2137 International Offices Visit the Digidesign Web site for contact information Web Site www.digidesign.com...
- Page 2 Copyright Important Safety Instructions When using electric or electronic equipment, basic precautions This guide is copyrighted ©2003 by Digidesign, a division of should always be followed, including the following: Avid Technology, Inc. (hereafter “Digidesign”), with all rights • Read all instructions before using this equipment.
-
Page 3: Table Of Contents
Configuring the 96i I/O in Pro Tools ........ - Page 4 96i I/O Guide...
-
Page 5: Chapter 1. Introduction To The 96I I/O
The 96i I/O supports sampling rates up to • BNC cable (1.5 foot [0.46m]) 96 kHz for superior dynamic range and low noise floor. The 96i I/O is the ideal audio inter- face to input multiple MIDI sound modules, System Requirements samplers, synthesizers, and other sound sources into Pro Tools|HD. -
Page 6: Digidesign Registration
Digidesign guides use the following conven- provide support for hardware and software it tions to indicate menu choices and key com- has tested and approved. For a list of Digidesign- mands: qualified computers, operating systems, hard drives, and third-party devices, refer to the latest... -
Page 7: About Www.digidesign.com
Development Partners and their plug-ins, applications, and hardware. News and Events Get the latest news from Digidesign; sign up for a Pro Tools demo. To learn more about these and other resources available from Digidesign, visit our Web site (www.digidesign.com). - Page 8 96i I/O Guide...
-
Page 9: Chapter 2. 96I I/O Hardware Overview
Figure 1. 96i I/O front panel Power Switch and LED Ring Loop Master LED This button turns the 96i I/O on and off. The LOOP MASTER LED indicates which HD au- dio interface is the master Pro Tools peripheral. The LED ring around the power button will light... - Page 10 INT (Internal) Indicates the 96i I/O is the Pro Tools clock master. DIG (Digital) Indicates the 96i I/O S/PDIF port is providing master clock to Pro Tools. LOOP (Loop Sync) Indicates 96i I/O is in Loop Slave mode, and is clocking to the current Loop Master device.
-
Page 11: 96I I/O Back Panel
–8 dBV. –10 dBV operating levels. Inputs 5–16 are software-switchable between The 96i I/O is factory calibrated at +14 dB head- –8 dBV and +4 dBu operating level sensitivity. room, yielding a maximum output level of The 96i I/O inputs can accommodate a wide +18 dBu when in +4 dBu operating mode. - Page 12 S/PDIF output is mirrored to analog outputs 1–2. Primary Port To maintain data integrity and minimize jitter, The Primary Port is used to connect the 96i I/O use only 75-ohm coaxial cable. to your HD cards, or to another HD-series audio interface, using a DigiLink cable.
-
Page 13: Chapter 3. Installing And Configuring The 96I
The 96i I/O is auto power-se- ration instructions. lecting (100V to 240V) and will work automati- If you are adding the 96i I/O to an existing cally when plugged into an AC power receptacle system, see the Expanded Systems Guide. -
Page 14: Powering Up Your System
Connect the BNC cable from the Loop Sync Out port of the primary HD I/O (192 I/O, Power down your system in this order: 192 Digital I/O, 96 I/O, or other 96i I/O) to the Quit Pro Tools. Loop Sync In port of the 96i I/O. -
Page 15: Checking Installation
To check installation using DigiTest: directly to the 96i I/O. Figure 2 illustrates a stu- Start up your computer (see “Powering Up dio setup with the 96i I/O connected to a mix- Your System”... -
Page 16: Configuring The 96I I/O In Pro Tools
Monitor Outs Sends and Returns Effects Devices Figure 2. 96i I/O studio setup with a mixing console Connection Tips Configuring the 96i I/O in Connect digital recorders such as CD and DAT Pro Tools recorders using the S/PDIF RCA outputs on the 96i I/O. - Page 17 Enabling S/PDIF Digital Input for output levels. Channels 1 and 2 To adjust input level sensitivity on the 96i I/O: You can choose to use either the analog or digi- Connect instrument and other devices to the tal inputs as sources for 96i I/O channels 1–2.
- Page 18 96i I/O Guide...
-
Page 19: Index
index Numerics 24-bit 1 Identify button 11 96-kHz 1 input sensitivity 13 setting 13 inputs analog 7 AC power 9 S/PDIF digital 8 power-up sequence 10 word clock 8 installation 9 balanced inputs 7 Loop Master 5 base rate 8 Loop Sync connections 10 In and Out 8... - Page 20 Sample Rate 5 sensitivity 13 setting input gain level 13 studio setup (no mixer) 11 Sync Mode 6 synchronization 10 unbalanced input 7 output 7 wiring TRS balanced input 7 TRS balanced output 7 word clock 8 96i I/O Guide...
Need help?
Do you have a question about the 96i I/O and is the answer not in the manual?
Questions and answers