Download Print this page

Tantalus ITRON SENTINEL TUNet PP-1316 Install Manual

Meter reader

Advertisement

INSTALL GUIDE
Sept 18, 2011
KT-109967
TUNet
ITRON SENTINEL
READER
®
PP-1316
®
METER
Tantalus Systems Corp.
301– 3480 Gilmore Way Burnaby BC V5G 4Y1 Canada
p 604.299.0458 | f 604.451.4111
www.tantalus.com

Advertisement

loading

Summary of Contents for Tantalus ITRON SENTINEL TUNet PP-1316

  • Page 1 ® INSTALL GUIDE TUNet PP-1316 Sept 18, 2011 ® ITRON SENTINEL METER KT-109967 READER Tantalus Systems Corp. 301– 3480 Gilmore Way Burnaby BC V5G 4Y1 Canada p 604.299.0458 | f 604.451.4111 www.tantalus.com...
  • Page 2 This Guide, and any associated software, is being provided to you only as a licensee pursuant to legal agreements with Tantalus Systems Corp. that govern your rights and all other aspects of the relationship, and prevail over the legal notices herein to the extent of any inconsistency.
  • Page 3 The device is specifically designed to be used under Section 15.247 of the FCC Rules and Regulations. Any unauthorized modification or changes to this device without the express approval of Tantalus Systems Corp. may void the user’s authority to operate this device.
  • Page 4: Table Of Contents

    T a b l e o f C o n t e n t s 1 :: Product Description..........................1 Product Specification: PP-1316 C&I Meter Reader ..............2 2 :: Installing the PP-1316 ........................... 3 Equipment Required........................3 Installing PP-1316 Components ....................4 2.2.1 Installing PP-1316 Components into the Itron SENTINEL®...
  • Page 5: Product Description

    1 :: Product Description The Tantalus PP-1316 Itron SENTINEL® Meter Reader joins the wireless connectivity of an Itron SENTINEL® Commercial and Industrial 3 phase meter to the metering features of the TUNet communication system fixed network. The PP-1316 adds wireless, two-way communications and advanced monitoring capabilities including: •...
  • Page 6: Product Specification: Pp-1316 C&I Meter Reader

    900 MHz Antenna (Part 15) Antenna within sealed meter not accessible to installer/operator. Standards • FCC CFR Title 47 Part 15c (Intentional Radiators) • ANSI C12.1:2008 Compliant • CFR Title 47 Part 15b (Unintentional Radiators) Page 2 Tantalus Systems Corp. Released 18/09/2011...
  • Page 7: Installing The Pp-1316

    2 :: Installing the PP-1316 Before the PP-1316 can be installed, the Itron SENTINEL® must be programmed with initial configuration settings. Energized meters, meter sockets and distribution lines present the risk of electrical shock. All work on this equipment should be performed by qualified metering specialists or industrial electricians.
  • Page 8: Installing Pp-1316 Components

    The PP-1316 is compatible with all Itron SENTINEL® meter forms. The following parts are supplied with the PP-1316 installation kit: Tantalus communication module, P/N 120-0215 Tantalus antenna bracket, P/N 260-0055 P P - 1 3 1 6 C o m p o n e n t s L i s t ( S i n g l e A s s e m b l y )
  • Page 9: Installing Pp-1316 Components Into The Itron Sentinel® Meter

    2.2.1 Installing PP-1316 Components into the Itron SENTINEL® Meter Remove the outer plastic cover from the Itron SENTINEL®. Unclip the Itron SENTINEL® display housing from its base by gently lifting the snap features in two locations. Slightly tilt the display housing away from the base to disengage the two pieces. Locate the set of four parallel ridges inside the display housing.
  • Page 10 Insert the Tantalus communications module ribbon cable between the two outer ridges. The ribbon cable should fit snugly between the two ridges. Firmly press the ribbon cable connector against the mating header underneath the Itron SENTINEL® communications board. To ensure proper connectivity, verify that the ribbon...
  • Page 11 Situate the PP-1316 module within the cavity inside the display housing. Ensure that the clip on the top of the display housing is used to lock down the PP-1316 module. Ensure that the coaxial cable falls within the hole on the side of the display housing. Snap the display housing back on the base of the meter.
  • Page 12 10. Snap the Tantalus bracket on the top of the meter. Also, there is a clip on the side of the bracket which guides the coaxial cable. Ensure the coaxial cable is placed inside the clip. If the coaxial cable has SMA RF connectors, mate them together.
  • Page 13: Configuring The Meter

    2.3 Configuring the Meter **** TBD **** TUNet PP-1316 Install Guide page 9 Doc No. KT-109967...
  • Page 14: Contact Information

    3 :: Contact Information T a n t a l u s S y s t e m s C o r p . Tantalus Systems Corp. 301 – 3480 Gilmore Way Burnaby, BC Canada V5G 4Y1 T/ 604.299.0458 F/ 604.451.4111 TECHNICAL SUPPORT TantalusTechSupport@tantalus.com...