Trouble Codes - Sharp AR-151 Service Manual

AR-F152
[9] SIMULATION, FAX SOFTWARE SWITCH, TROUBLE CODES
1. List of simulations
The simulations for the AR-F152 (with Fax functions) are shown in bold fonts.
Sim Kind of Sub
No. main code code
01 Optical 01
system
02 SPF 02
Individual 03
load 04
operation 05
06
07
05 Lamp ON 01
check 02
03
06 Machine 01
individual 02
load
operation
07 Aging 01
06
08 High 01
voltage 02
output check 03
06
10 Other None
14 Trouble None
reset
16 U2 trouble None
reset
20 Maintenance 01
counter
clear
21 Counter 01
setup 02
(When
maintenance)
22 Counter 01
display
02
04
05
06
08
12
14
17
18
20
21
22
23
24
24 Special 01
counter 04
clear 06
07
08
09
10
11
13
14
25 Main motor 01
ON
10
Operation
Mirror scan operation
SPF sensor status display
Motor ON
Paper feed solenoid ON
Pressure release solenoid ON
(RSPF)
Resist clutch ON (RSPF)
Gate solenoid ON (RSPF)
Operation panel display check
Fusing lamp ON + Cooling fan
HIGH/LOW speed
Copy lamp ON
Paper feed solenoid ON
Resist solenoid ON
Warm up display and aging with
jam
Intermittent aging
Developing bias
Main charger (Grid high)
Grid voltage (Low)
Transfer charger
Toner motor aging
Cancel troubles other than U2
Cancel of U2 trouble
Maintenance/mini-maintenance
counter clear
Maintenance cycle setup
Mini-maintenance cycle setup
Maintenance/mini-maintenance
counter display
Maintenance/mini-maintenance
preset display
Jam total counter display
Total counter display
Developer counter display
SPF counter display
Drum counter display
P-ROM version display
Copy counter display
Printer counter display
FAX print counter display
Scanner counter display
SPF jam total counter display
FAX reception counter display
FAX transmission counter
display
Jam total counter clear
SPF counter clear
Developer counter clear
Drum counter clear
Copy counter clear
Printer counter clear
FAX transmission/reception
counter clear
FAX print counter clear
Scanner counter clear
SPF jam total counter clear
Main motor system ON + Cooling
fan low speed (For the duplex
model, the duplex motor is
simultaneously turned on.)
Polygon motor ON
Sim Kind of Sub
No. main code code
26 Various
setup
30 Sensor
operation
check
(Standard
provision)
43 Fusing
temperature
setup
46 Exposure
adjustment
48 Magnification
ratio
correction
50 Lead edge
adjustment
51 Timing
adjustment
61 Laser
system
operation
63 Shading
64 Self print
66 FAX PWB None
check
67 Program
Download
9 – 1
Operation
01 Manual feed setup
02 SPF setup
03 Second cassette setup
04 Machine duplex setup
06 Destination setup
07 Machine conditions check
20 Rear edge void setup
30 CE mark conformity control
ON/OFF setup
37 Cancel of stop at developer over
39 Memory capacity setup
40 Polygon motor OFF time setup
42 Transfer ON timing control setup
43 Side void setup
44 SPF document rear edge read
setup
47 FAX document rear edge scan
setup
55 CRUM destination display
01 Paper sensor status display
01 Normal copy
04 Fusing temperature setup 2
05 Duplex mode fusing temperature
setup
09 Postcard size paper fusing control
setup
01 Copy density adjustment
12 FAX density overall adjustment
13 FAX density adjustment
(Standard mode)
14 FAX density adjustment (Fine
character mode)
15 FAX density adjustment (Super
Fine mode)
γ Table adjustment (Copy mode)
19
01 Front/rear scan direction
01 Lead edge image position
adjustment
Paper lead edge/rear edge void
adjustment
10 Paper center offset +
OC/Document center offset +
SPF document center offset
18 Memory reverse position
adjustment
19 Duplex copy rear edge void
adjustment
02 Resist quantity adjustment
06 SPF exposure correction
03 Polygon motor check
(HSYNC output check)
01 Shading check
01 Self print only with the engine (1
by 2 mode)
Simulation on the FAX panel
(For details, refer to the FAX
simulation.)
14 PCL PWB program download