Advertisement
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the
voltage marked on the name plate.
2. Never use the tool if its cover or any bolts are missing.
If the cover or bolts have been removed, replace
them prior to use. Maintain all parts in good working
order.
3. Always secure tools when working in elevated
positions.
4. Never touch the blade, drill bit, grinding wheel or other
moving parts during use.
5. Never start a tool when its rotating component is in
contact with the workpiece.
6. Never lay a tool down before its moving parts have
come to a complete stop.
7. ACCESSORIES: The use of accessories or
attachments other than those recommended in these
instructions might present a hazard.
8. REPLACEMENT PARTS: When servicing use only
identical replacement parts.
SPECIFIC SAFETY RULES FOR BLOWER VAC
1. Do not use the machine to pick up humid material water,
liquids, pieces of glass, iron, stones or tin cans, this
could be very dangerous for you and the machine.
2. Do not use the machine to pick up hot embers or
material which is burning, smoking or smoldering. Do
not use the machine to pick up lit cigarettes. Do not use
the machine to pick up material which has been
contaminated by flammable or explosive materials. Do
not suck in highly flammable fumes. Always check that
the material picked up by your machine is not
flammable, toxic or explosive.
3. Do not use the vacuum mode without the dust bag in
place.
4. Always keep the area to be cleaned free from wires,
stones, debris, tin cans and other obstacles.
5. Avoid collisions with hard objects which could damage
your machine.
6. Keep bystanders and animals at least 5m away from the
working area.
7. Do not manually insert objects into the blower/vacuum
tube.
8. Do not put part of your body such as your hands and
fingers into the vacuum opening or exhaust opening.
9. Hold the machine firmly in both hands when working
with it.
10. Always use the machine with the blower vac tubes in
place.
DESCRIPITION
1. Mains cable
2. Rear handle
3. On/Off switch
4. Front handle
5. Suction/blower tube
6. Motor housing
7. Change-mode lever
8. Vacuum bag
9. Support wheel
SPECIFICATIONS
Voltage
Power input
No load speed
Dust bag capacity
Air velocity
Air volume
Mulching ratio
Net weight
STANDARD ACCESSORIES
Screw x 1, Shoulder strap x 1
ASSEMBLY
ASSEMBLE THE TUBE AND WHEEL BRACKET
1. Insert the lower tube to the upper tube and align the
screw hole in the upper tube with the screw hole in the
lower tube, at the same time the convex plate can match
the slot on upper tube firmly. (Fig. 1)
2. Locate one screw (A) (ST4.2x45) in big screw hole on
upper tube. Tighten the screw securely and torque to
1.2 Nm minimum. (Fig. 2)
FITTING THE VACUUM BAG
1. Connect the strap onto the hook in the housing. (Fig. 3)
2. Attach the push-on vacuum bag connector to the outlet
tube of the housing. Push the fitting of the vacuum bag
directly onto the outlet until it "clicks" into position. (Fig. 4)
3. To remove the vacuum bag, disconnect the attachments
in the reserve order. (Fig. 5)
4. When removing the fitting on the outlet, first depress the
button in front of the plastic connector, and then push.
(Fig. 6)
OPERATION
BEFORE STARTING
Before starting the machine, make sure that the vacuum
bag is fitted and the shoulder strap is adjusted to suitable
working position.
BLOWING MODE
Before starting the machine, make sure that the vacuum
bag is fitted and the shoulder strap is adjusted to suitable
working position.
• Turn the "change-mode" lever (7) anti-clockwise to the
blow mode position. (Fig. 7)
• Turn the switch to on, point the jet of air in front of you and
move forward, slowly to gather the leaves or to move the
leaves from inaccessible areas.
4
230 ~ 50Hz
3000W
15000min
-1
40L
300km/h
16m
/min
3
10:1
3.0kg
Advertisement
