Using Mmc/Sd Card Devices - Philips LPC3180 Application Note

Philips Semiconductors
usbcore: registered new driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.1:USB FTDI Serial Converters Driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0
.12
usb_register_udc returned 0
USB probe done
gs_module_init: Gadget Serial v2.0 loaded
ip3506: start_otg_ip3506
ip3506: ip3506_otg_probe
data->container = c0229244
host = 1
a_bus_req = 1
gadget = 1
id = 1
b_sess_end = 1
ip3503_udc_notification: reason 0
spi_init
SPI : setting spi-1 control to 804E93
Adapter c1b35078 Adapter spi-1
spi-lpc : Adapter spi-1 registered at 20088000 using irq 55
SPI : setting spi-2 control to 804E93
Adapter c168cce0 Adapter spi-2
spi-lpc : Adapter spi-2 registered at 20090000 using irq 44
spi-lpc : Driver version 1.5 registered
setting divider code to 18 (ratio=38) using base clock = 104000000 freq out
2736842
spi_readtest_init
done spi_readtest_init
NAND device: Manufacturer ID: 0x20, Chip ID: 0x35 (ST Micro NAND 32MiB 1,8V
8-bit)
Scanning device for bad blocks
Bad eraseblock 478 at 0x00778000
Bad eraseblock 1520 at 0x017c0000
Creating 1 MTD partitions on "NAND 32MiB 1,8V 8-bit":
0x01000000-0x01f00000 : "LPC3180 NAND PART 0"
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
mmc-lpc3180: mmc/sd driver running on platform=lpc3180
: MMCI rev 0 cfg 00 at 0x20098000 irq 15,13
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
running on [console=ttyS0,115200n8 root=/dev/ram initrd=0x80800000,12M]
Mounting SD/USB storage
No SD card or unknown filesystem
No USB storage or unknown filesystem
INIT: Entering runlevel: 2
Creating the the /var/dev/ttySA* links
Starting internet superserver: inetd.
Copacabana - ARM Embedded Linux version 1.1-vfp
Monday 20 December 2004 @ 20:40
(none) login: root
BusyBox v0.60.5 (2004.05.11-13:49+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ #

4.2 Using MMC/SD card devices

When you insert a SD card at boot time, Linux will automatically detect that and try to
mount the device. If you do so later you will have to mount the device manually.
<12NC>
Application note
process c057faa0
process c057f820
Rev.03 — 21 Dec 2006
AN10476
Getting started Linux with LPC3180
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
11 of 28