Subscribe to Our Youtube Channel
Related Manuals for Tohken THIR-6000 Bluetooth Series
Summary of Contents for Tohken THIR-6000 Bluetooth Series
- Page 1 THIR-6000 Bluetooth Series THIR-6000B THIR-6000HB THIR-6000DM-B Handheld Image Reader (Linear / 2D Scanner) OPERATION MANUAL TOHKEN CO., LTD. 1st Edition April 15, 2008...
- Page 2 [Memorandum]...
- Page 3 Tohken makes no guarantee of performance or suitability of its products, nor does Tohken assume any liability that occurs from the use of the product. Tohken reserves the right to make changes to its products and this document without any notice.
-
Page 4: Safety Notice
Introduction Thank you for purchasing this product. This manual explains the features of this product, operation, system configuration, specifications, etc. In order to use the product properly, please read this manual carefully. When there is any problem during normal use, please document it carefully to be reproduced by our support team. The contents of this manual may be changed without a notice. -
Page 5: Handling With Care
Handling with care CAUTION About backup data This product has a memory backup function. This backup can not guaranteed if repair, reconstruction, and upgrade are performed on this Image Reader. CAUTION Please do not use this product at temperature or humidity ranges that are different from the product specifications or under the direct sunshine. - Page 6 CAUTION This unit is designed to use with general electronics devices such as personal computer, office automation equipment, mesurement hardware, industrial robot, AV device etc. Please care specially if try to use for safety unit of transportation vehicle (cars, train, airplane), traffic right, gas leak sensor or other device for safety.
-
Page 7: Where To Store
Where to store CAUTION Please do not use/store this unit in the following environment to avoid electrification, fire, defect on the unit, cause damage on other device placed around. - The temperature or humidity is out rage of the Specification. - There is a danger of water leakage and electricity leakage. -
Page 8: Unpacking The Product
Unpacking the product After opening the shipping package containing the THIR-6000, take the following steps: 1- Check for damage that might occur during the shipping process. Report the damage immediately to the carrier who delivered the shipment. 2- Save the shipping container for later storage or shipping. 3- Make sure everything ordered is present. -
Page 9: Table Of Contents
Table of Content INTRODUCTION ..............................I SAFETY NOTICE..............................I HANDLING WITH CARE............................II WHERE TO STORE..............................IV CAUTION ............................IV PLEASE DO NOT USE/STORE THIS UNIT IN THE FOLLOWING ENVIRONMENT TO AVOID ELECTRIFICATION, FIRE, DEFECT ON THE UNIT, CAUSE DAMAGE ON OTHER DEVICE PLACED AROUND..............................IV LONG-TERM STORAGE.............................IV WIRELESS DEVICE.............................IV UNPACKING THE PRODUCT........................... - Page 10 5.1 G ..........................16 ENERAL SPECIFICATIONS 5.2 F ........................17 UNCTIONAL SPECIFICATION 5.3 R ..........................18 EADING ANGE EPTH 5.4 D ............................22 EFAULT SETTINGS 6. DIMENSIONS..............................23 6.1H ...........................23 OUSING IMENSIONS 7. SPECIALTY FUNCTION..........................24 7.1 G ............................24 LOBAL HUTTER 7.2 A ..........................26 UTO DETECTION MODE 7.2.1 Overview ..............................26 7.2.2 How to use...............................27 7.3 F...
- Page 11 Is the connection disconnected during transmitting?................35 8.7 K ....................36 EYBOARD WEDGE INTERFACE IS NEEDED 8.8 PIN CODE ........36 IS REQUIRED WHEN LUETOOTH CONNECTION IS ESTABLISHED APPENDIX 1 CRADLE（TBC-6000）......................37...
-
Page 12: Getting Started
1. Getting started Equipped with a powerful state-of-the-art 2D Imager Scanner and processing CPU, the THIR-6000 is ready to capture images as well as decoding 1D or 2D bar codes. The THIR-6000 is a 2D Imager Scanner that reads Liner, 2D, and Postal barcodes to meet many different requirements in Delivery, Transportation, Meter Reading, and many other applications. - Page 13 3) Ordering information THIR-6000 (H) (DM) B 1. Resolution If “H” follows “THIR-6000”, the scanner is high resolution type. And if there is no “H”, the scanner is normal resolution type. 2. Direct Parts Marking If “DM” follows “THIR-6000” or “THIR-6000H”, the scanner is for direct parts marking application.
-
Page 14: Scanner Components
1.1 Scanner components Reading Window Reading Switch Grip Handle Charging terminal Figure1a. Front View... - Page 15 Indicator for battery status Indicator for Wireless connection Monitoring LED Buzzer hole Guide for setting-on to the cradle Figure1b. Side and rear View...
-
Page 16: How It Works
1.2 How it works • Monitoring LED The monitoring LED lights up either GREEN or RED depending on the operation: GREEN light indicates the completion of successful decoding of a symbol. Flashing GREEN light indicates the image data transmission in progress. RED light indicates the failure of data transmission. -
Page 17: How To Use Thir-6000B
2. How to use THIR-6000B 2.1. Battery charging THIR-6000B employs Li-ion rechargeable battery. Since new batteries are not fully charged, please charge the battery by following the instruction below. Setting THIR-6000B on to the cradle starts charging the battery. *Please see “Appendix 1” for more information about the cradle. 1. - Page 18 3. The indicator for battery status will change to orange. When the battery is fully charged, it will turn green. Normally, the charging time is 3 hours. Indicator for battery status Green: Remained enough Orange: Charging Red: Low battery CAUTION Charging time is varied depending on remained amount Please set THIR-6000B correctly to the cradle otherwise charging process may be failed Dust and dirt on the charging terminal may prevent to be charged correctly.
-
Page 19: Etting Up The Ost Omputer
2.2 Setting up the Host Computer THIR-6000 can be connected to the host computer even when it is being charged. 2.2.1 Preparation Install the software comes with Bluetooth adopter. *Please see the operation manual of the adapter. Start the software Connect THIR-6000B with the software. -
Page 20: Setting Virtual Com Port
2.3 Setting virtual COM port 2.3.1. Communication settings By using profile of Bluetooth (SPP), THIR-6000B can be communicated with the host computer through virtual COM port. Communication settings, like baud rate or frame structure, are not valid for THIR-6000B. 2.3.2. Communication protocol Communication protocol is not needed to be set. -
Page 21: Operation
3. Operation 3.1 Barcode reading • Once the user pulls the reading switch, the THIR-6000 shows two red points by LED light to indicate the proper reading area. Note: The unit turns off the red dot-shaped laser pointer automatically after 30 seconds if there is no reading operation. -
Page 22: Beeping Sounds
3.2 Beeping Sounds Event or Status of scanner Sounds Power ON beeps 5 times (long, long, short, short, short) Succeeded in reading Short beep 1 time Fails to transmit the data Short beeps 7 times On all the other occasions remains silent 3.3 Image data transaction *) THIR-6000U as a HID can not capture images.
Need help?
Do you have a question about the THIR-6000 Bluetooth Series and is the answer not in the manual?
Questions and answers