CoverCraft Form-Fit Use And Care Instructions

2 - Rinse the cover twice (2X) to remove all the cleaner.
3 - Air dry, or use a dryer set on Permanent Press heat setting.
A cover may also be cleaned by turning it inside-out on the vehicle.
1 - Mix one ounce Simple Green All-Purpose Cleaner per quart of warm water.
2 - Spray or sponge onto cover.
3 - Rinse with plain water (until no suds) and allow to air dry.
Simple Green is available in most world markets.
If you have any questions, contact them at www.australia.simplegreen.com
LIMITED FOUR (4) YEAR WARRANTY
Form-Fit™ fabric covers are warranted for four years from date of purchase to the original
purchaser. Save your receipt! Warranty coverage protects against defects in material and
workmanship, as well as the fabric becoming unserviceable during normal use. After factory
inspection, we will repair or replace the cover or specific panels judged to be unusable.
Warranty does not cover fading, which occurs naturally on all products used outdoors. This
fabric is not waterproof - it is breathable to allow moisture, condensation and heat to escape
from under the fabric.
In case of Warranty Claim
STORMCOVERS AUSTRALIA PTY LTD
UNIT 2 / 37 PREMIER CIRCUIT
WARANA
QLD - 4575 - AUSTRALIA
Tel 07 5493 1400
orders@coverworld.com.au
NOTE - Car covers are not designed for use when towing. Serious damage
can occur to the cover and the paint surface of the vehicle may also be
damaged. If you use a cover for towing, you do so at your own risk.
Keep your original invoice
as proof of purchase
Form # 1320012 Fx (02/10)
Form-Fit® premium quality indoor custom covers are manufactured with a
polyester knit fabric that has spandex in the yarns to allow the cover to stretch and
follow the contours of the vehicle. The addition of spandex helps the fabric retain
its original memory so the cover doesn't get "baggy" after extended use. During the
production process soft cotton loop is knitted in on the underside and then sheared
to a soft luxurious fleece-like finish. The material is breathable and soft against any
fine paint finish.
If your vehicle has an outside radio antenna which will not retract flush with
the vehicle body, you will have to provide an opening in the cover. We have
included a non-corrosive plastic grommet set for the antenna opening.
1) The most accurate way to make an antenna opening is to remove the antenna
and install the cover on the vehicle, making sure it is properly aligned and
positioned. Using a sharp pencil, punch a hole through the fabric at the antenna
location. Be careful to avoid hitting the vehicle finish with the pencil. If the antenna
is not easily removed, see procedure #2.
2) Place the cover on the vehicle except for the fender or body panel where the
antenna is located. For example, if the antenna is located on the front passenger
side fender, roll or fold the cover away from the antenna and cover all the remaining
area of the vehicle. (Do not attempt to place the cover over the top
Center the cover, align both seams with the roof edges and be sure the cover is
pulled down evenly over the front and rear bumpers. Carefully unfold the portion
of the cover that is next to the antenna and position it next to the base of the antenna.
Recheck the overall positioning of the cover to make sure it has not moved on the
vehicle. Make sure the cover lies flat over the hood and roof areas of the vehicle.
Mark the cover with the location of the antenna base and make a hole with a sharp
pencil.
Use sharp scissors to make the hole opening 1/2 inch in diameter and install the
grommet as shown in the diagram to the right. The outside grommet ring fit is very
tight. Place the cover on a CLEAN hard surface, position the the inside grommet
through the opening you made
and then secure the outside grom-
met snap-ring in place using a
rubber mallet. Do NOT use ex-
cessive force or the ring can be
damaged. Do NOT install the
grommet with the cover on the
vehicle.
Use and Care
Instructions
of t
he antenna.)
1/2