Related Manuals for Hewlett Packard Enterprise FM 3180
Summary of Contents for Hewlett Packard Enterprise FM 3180
- Page 1 HPE Composable Fabric 5.0 FM 3180 Fabric Module Installation Guide Part Number: P14110-001a Published February 2019 Edition: 2...
-
Page 2: Acknowledgements
Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein. -
Page 3: Table Of Contents
Record the MAC Address ............................ 1 1 Installation Considerations .......................... 1 1 Power.......................................... 1 1 Working with Optical Cables ................................ 1 1 Installing HPE FM 3180........................12 Rack Mounting HPE FM 3180 .......................... 1 2 Establishing a Management Connection ...................... 1 3 Establishing a Console Connection ............................... 1 3 Establishing a Management Network Connection using an IPV6 Link-Local Address ........ 1 4 Powering Up FM 3180 ............................ 1 4 Configuring the Fabric Module .......................... 1 4 Connecting the Composable Fabric ........................ 1 4 FM 3180 Installation Guide... - Page 4 Front Panel SFP and QSFP Ports .......................... 3 1 QSFP28 LEDs ................................ 3 1 SFP LEDs .................................. 3 2 Management Panel .............................. 3 2 Power Supply LED .............................. 3 3 Fan LED .................................. 3 3 Hot Swap Fan and Power Modules ..................... 34 Replacing a Power Supply Module ........................ 3 4 Replacing a Fan Module ............................ 3 4 FM 3180 Specifications ........................35 FM 3180 Installation Guide...
-
Page 5: Introduction
Introduction The HPE FM 3180 fabric module is a 48 port 25 GbE and 8 port 100 GbE fabric module in a 1U form factor that provides 2.0 Tbps Bandwidth, ideally suited for Datacenter top of rack deployments. The FM 3180 supports port level configuration of 48 10 GbE or 25 GbE SFP ports and eight 100 GbE QSFP28 ports. -
Page 6: Safety Notes
• Keep replacement parts in their original static-free packaging. • Remove all plastic, foam, vinyl, paper, and other static-generating materials from the work area. • Whenever possible, use tools that do not create electrostatic discharge. FM 3180 Installation Guide... -
Page 7: Regulatory Compliance
Regulatory Compliance FM 3180 complies with the following regulatory certificates: EN 55022:2010/AC:2011 EN 61000-3-2:2014 EN 61000-3-3:2013 EN 55024:2010 IEC 61000-4-2 ed2.0 (2008-12) IEC 61000-4-3 ed3.2 Consol with am1&2 (2010-04) IEC 61000-4-4 ed3.0 (20012-04) IEC 61000-4-5 ed3.0 (2014-05) IEC 61000-4-6 ed4.0 (2013-10) IEC 61000-4-8 ed2.0 (2009-09) -
Page 8: Checklist
HPE Composable Fabric Module Administrator Guide using Linux and CLI. q Configure the fabric module and the Composable Fabric using the Composable Fabric Manager UI as described in HPE Composable Fabric Manager UI Online Help q Connect servers to access ports FM 3180 Installation Guide... -
Page 9: Pre-Installation
Equipment Protection Choose an area where liquids or other foreign objects cannot fall onto the equipment or be drawn into ventilation holes. Equipment Specifications Refer to the fabric module specifications in chapter 11, FM 3180 Specifications. FM 3180 Installation Guide... -
Page 10: Ups
For any UPS (Uninterruptible Power Supply) providing power to an HPE FM 3180 fabric module, HPE recommends the following: • The UPS must have enough capacity to power the fabric module plus any other equipment that is connected to the UPS. -
Page 11: Part Numbers
Part Numbers FM 3180 is available with two AC power supplies. The power supplies can be ordered to exhaust out the back or front panel. FM 3180 is available with hot-swappable fans that either exhaust out the back (power) panel (red) or out the front (I/O) panel (blue). -
Page 12: Installing Hpe Fm 3180
I/O connections. To install an HPE FM 3180 or FM 3180 fabric module that lacks center mounting holes in a rack: 1. Determine the 1-U slot position in the rack. -
Page 13: Establishing A Management Connection
Linux and the CLI. For serial access, the console system must be connected to the console port on the fabric module. To connect to the serial console port, use the following settings: • 115.2 Kbps • 8 data bits FM 3180 Installation Guide... -
Page 14: Establishing A Management Network Connection Using An Ipv6 Link-Local Address
Source output interface ID Example: ssh admin@fe80::216:eaff:fe5f:4cad%e Powering Up FM 3180 When you connect one or both power supplies and provide site power to the fabric module, it automatically powers up. There is no power switch. Configuring the Fabric Module The HPE Composable Fabric module is shipped configured to use DHCP. -
Page 15: Creating The Composable Fabric
QSFP). • HPE FM 3180, FM 3032Q, FM 2072, 2, 2s, 2p, 2sp and 3eq fabric modules running at 10 Gbps per port (40 Gbps per QSFP). IMPORTANT: For Composable Fabric paths between fabric modules, you must make sure that all fabric modules use the same fabric port speed. -
Page 16: Creating A Composable Fabric Using Fm 1006 Passive Interconnect Modules
FM 1006 passive interconnect modules. Using FM 1006 modules, you can create a network topology that includes FM 3032Q, FM 2072, and FM 3180 as well as models 2e, 3eq, 2p, 2S and 2sp. IMPORTANT: In a mixed configuration, if the fabric contains an FM 2072 or models 1, 2, 2s, 2sp or 2e models that run at 10 Gb/s per port, the FM 3032Q ports must be set to operate at 10/40 Gb/s per port for compatibility. -
Page 17: Connecting Fm 3180 Fabric Ports To An Fm 1006
The following illustration shows a network topology that connects the Composable Fabric across two racks using four FM 3180 fabric modules connected through an FM 1006 passive interconnect module. Note that all unused FM 1006 ports are looped back using loopback cables. -
Page 18: Looping Back Unused Fm 1006 Ports
3, 5, 10, 20 and 100M). You need six cables to expand an FM 1006 device to other FM 1006 devices. For part numbers and descriptions of supported cables, refer to the document, HPE Composable Fabric Compatibility Matrix. FM 3180 Installation Guide... -
Page 19: Creating A Direct Connect Composable Fabric
To help in cabling the fabric, number the FM 3180 modules in the fabric starting with 1. For example, if you are connecting five FM 3180 modules, number them 1, 2, 3, 4, 5. You can affix a label to each fabric module for identification. Refer to the appropriate section that follows for your fabric size. -
Page 20: Three-Module Fabric
Three-Module Fabric These are the connections to create a Composable Fabric consisting of 3 FM 3180 modules. From From From Module 1 Module 2 Module 3 Module 2 52 Module 3 52 Module 1 52 Module 3 54 Module 1 54... -
Page 21: Four Module Fabric
Four Module Fabric These are the connections to create a Composable Fabric consisting of 4 FM 3180 modules. From From From Module 1 Module 2 Module 3 Module 2 52 Module 3 548 Module 4 52 Module 3 54 Module 4 54... -
Page 22: Five-Module Fabric
Five-Module Fabric These are the connections to create a Composable Fabric consisting of 5 FM 3180 modules. From From From Module 1 Module 2 Module 3 Module 2 52 Module 3 52 Module 4 52 Module 3 54 Module 4 54... -
Page 23: Six-Module Fabric
Six-Module Fabric These are the connections to create a Composable Fabric consisting of 6 FM 3180 modules. From From From Module 1 Module 2 Module Module 2 52 Module 3 52 Module 4 52 Module 3 54 Module 4 54... -
Page 24: Seven Module Fabric
Seven Module Fabric These are the connections to create a Composable Fabric consisting of 7 FM 3180 modules. Begin with Module 1, then Module 2, and finish with the Module 7 connections to fabric modules 1, 2, and 3. From... -
Page 25: Adding A Fabric Module To An Existing Fabric
Adding Module #7 to a Six-Module Fabric You have an existing fabric with six FM 3180 fabric modules. You want to add another FM 3180 to make it a fabric of seven. To add the fabric module, you need to shift six existing connections and add three more cables. -
Page 26: Adding Module #6 To A Five-Module Fabric
To add the fabric module, you need to shift six existing connections and add three more cables. You start changing connections with HPE FM 3180 3 55, then HPE FM 3180 4, next HPE FM 3180 5, and finally number 6. The following table lists the re-cabling required by direction. -
Page 27: Adding Module #5 To A Four-Module Fabric
Adding Module #5 to a Four-Module Fabric You have an existing fabric with four FM 3180 fabric modules. You want to add another FM 3180 to make it a fabric of five. To add the fifth fabric module, you need to shift six existing connections and add three new cables. -
Page 28: Adding Module #4 To A Three-Module Fabric
Adding Module #4 to a Three-Module Fabric You have an existing fabric with five FM 3180 fabric modules. You want to add another FM 3180 to make it a fabric of six. To add the fabric module, you need to shift six existing connections and add three more cables. -
Page 29: Adding Module #3 To A Two-Module Fabric
Adding Module #3 to a Two-Module Fabric You have an existing fabric with five FM 3180 fabric modules. You want to add another FM 3180 to make it a fabric of six. To add the fabric module, you need to shift six existing connections and add three more cables. -
Page 30: Installing Transceivers And Cables
You should have the transceivers you ordered for your HPE fabric module. The FM 3180 supports Quad Small Form-Factor Pluggable (QSFP28) transceivers in QSFP ports 49-56. Important: Fiber optic modules are dust-sensitive. Always keep the plug in the optical bore when a fiber optic cable is not installed or when you store the module. -
Page 31: Ports And Leds
Ports and LEDs Front Panel SFP and QSFP Ports FM 3180 contains 48 SFP28 ports and 8 QSFP28 ports as illustrated below. QSFP28 ports 51-56 are used for Composable Fabric connections to other Composable Fabric modules. QSFP28 ports 49 and 50 can be used for Access or Uplink connections. These QSFP28 ports can remain single 100 GbE ports or they can break out into four 25 GbE SFP ports per QSFP282 port. -
Page 32: Sfp Leds
STAT Fast Flash Started and is initializing. Slow Flash Initialized but has not yet connected to HPE Control. Solid Green Connected to HPE Control and operating properly. FM 3180 Installation Guide... -
Page 33: Power Supply Led
There is no power to either power supply. Fan LED Each of the fans has an LED as shown here: The fan LED states are: State Meaning green The fan is plugged in and running. The fan is not operating. FM 3180 Installation Guide... -
Page 34: Hot Swap Fan And Power Modules
2. Insert the replacement fan module into the chassis slot until fully seated and the latches snap into place. NOTE: Each fan module is keyed to insure correct orientation. 3. Verify that the Fan LED lights solid green. FM 3180 Installation Guide... -
Page 35: Fm 3180 Specifications
3+1 redundant fans, front to back and back to front system cooling EMC: CN(GB9254-2008), EU(EN55022, EN55024), Approvals FCC, VCCI, CCC Safety: IEC60950-1, GB4943, UL/CSA, CB, CCC Composable Fabric 6 x QSFP+ ports connect to the Composable Fabric. FM 3180 Installation Guide...
Need help?
Do you have a question about the FM 3180 and is the answer not in the manual?
Questions and answers